-
Notifications
You must be signed in to change notification settings - Fork 98
FSAVE_FNSAVE
Intel Architecture Software Developer's Manual (July 2017)
FSAVE / FNSAVE - Store x87 FPU State
| Opcode | Instruction | 64-Bit Mode | Compat/ Leg Mode | Description |
| 9B DD /6 | FSAVE m94/108byte | Valid | Valid | Store FPU state to m94byte or m108byte after checking for pending unmasked floating-point exceptions. Then re-initialize the FPU. |
| DD /6 | FNSAVE* m94/108byte | Valid | Valid | Store FPU environment to m94byte or m108byte without checking for pending unmasked floating- point exceptions. Then re-initialize the FPU. |
- See IA-32 Architecture Compatibility section below.
Stores the current FPU state (operating environment and register stack) at the specified destination in memory, and then re-initializes the FPU. The FSAVE instruction checks for and handles pending unmasked floating-point exceptions before storing the FPU state; the FNSAVE instruction does not.
The FPU operating environment consists of the FPU control word, status word, tag word, instruction pointer, data pointer, and last opcode. Figures 8-9 through 8-12 in the Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 1, show the layout in memory of the stored environment, depending on the operating mode of the processor (protected or real) and the current operand-size attribute (16-bit or 32-bit). In virtual-8086 mode, the real mode layouts are used. The contents of the FPU register stack are stored in the 80 bytes immediately follow the operating environment image.
The saved image reflects the state of the FPU after all floating-point instructions preceding the FSAVE/FNSAVE instruction in the instruction stream have been executed.
After the FPU state has been saved, the FPU is reset to the same default values it is set to with the FINIT/FNINIT
The FSAVE/FNSAVE instructions are typically used when the operating system needs to perform a context switch, an exception handler needs to use the FPU, or an application program needs to pass a “clean” FPU to a procedure.
The assembler issues two instructions for the FSAVE instruction (an FWAIT instruction followed by an FNSAVE instruction), and the processor executes each of these instructions separately. If an exception is generated for either of these instructions, the save EIP points to the instruction that caused the exception.
This instruction’s operation is the same in non-64-bit modes and 64-bit mode.
IA-32 Architecture Compatibility
For Intel math coprocessors and FPUs prior to the Intel Pentium processor, an FWAIT instruction should be executed before attempting to read from the memory image stored with a prior FSAVE/FNSAVE instruction. This FWAIT instruction helps ensure that the storage operation has been completed.
When operating a Pentium or Intel486 processor in MS-DOS compatibility mode, it is possible (under unusual circumstances) for an FNSAVE instruction to be interrupted prior to being executed to handle a pending FPU excep- tion. See the section titled “No-Wait FPU Instructions Can Get FPU Interrupt in Window” in Appendix D of the Intel® 64 and IA-32 Architectures Software Developer’s Manual, Volume 1, for a description of these circumstances. An FNSAVE instruction cannot be interrupted in this way on later Intel processors, except for the Intel QuarkTM X1000 processor.
(* Save FPU State and Registers *)
DEST[FPUControlWord] ← FPUControlWord;
DEST[FPUStatusWord] ← FPUStatusWord;
DEST[FPUTagWord] ← FPUTagWord;
DEST[FPUDataPointer] ← FPUDataPointer;
DEST[FPUInstructionPointer] ← FPUInstructionPointer;
DEST[FPULastInstructionOpcode] ← FPULastInstructionOpcode;
DEST[ST(0)] ← ST(0);
DEST[ST(1)] ← ST(1);
DEST[ST(2)] ← ST(2);
DEST[ST(3)] ← ST(3);
DEST[ST(4)]← ST(4);
DEST[ST(5)] ← ST(5);
DEST[ST(6)] ← ST(6);
DEST[ST(7)] ← ST(7);
(* Initialize FPU *)
FPUControlWord ← 037FH;
FPUStatusWord ← 0;
FPUTagWord ← FFFFH;
FPUDataPointer ← 0;
FPUInstructionPointer ← 0;
FPULastInstructionOpcode ← 0;
The C0, C1, C2, and C3 flags are saved and then cleared.
None.
#GP(0) If destination is located in a non-writable segment. If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit. If the DS, ES, FS, or GS register is used to access memory and it contains a NULL segment selector. If a memory operand effective address is outside the SS segment limit. #SS(0) CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #NM If a page fault occurs. #PF(fault-code) If alignment checking is enabled and an unaligned memory reference is made while the #AC(0) current privilege level is 3. If the LOCK prefix is used. #UD
#GP If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit. #SS If a memory operand effective address is outside the SS segment limit. #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #UD If the LOCK prefix is used.
#GP(0) If a memory operand effective address is outside the CS, DS, ES, FS, or GS segment limit. #SS(0) If a memory operand effective address is outside the SS segment limit. #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #PF(fault-code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory reference is made. #UD If the LOCK prefix is used.
Same exceptions as in protected mode.
#SS(0) If a memory address referencing the SS segment is in a non-canonical form. #GP(0) If the memory address is in a non-canonical form. #NM CR0.EM[bit 2] or CR0.TS[bit 3] = 1. #MF If there is a pending x87 FPU exception. #PF(fault-code) If a page fault occurs. #AC(0) If alignment checking is enabled and an unaligned memory reference is made while the current privilege level is 3.