[PW_SID:907681] [v3] Bluetooth: btusb: Add MT7925 support for ID 0x13d3:0x3608 #1977
Conversation
This file contains bidirectional Unicode text that may be interpreted or compiled differently than what appears below. To review, open the file in an editor that reveals hidden Unicode characters.
Learn more about bidirectional Unicode characters
Move MediaTek Bluetooth power off command before releasing usb ISO interface. Signed-off-by: Chris Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add disconnect callback function in btusb_disconnect which is reserved for vendor specific usage before deregister hci in btusb_disconnect. Signed-off-by: Chris Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
MediaTek claim an special usb intr interface for ISO data transmission. The interface need to be released before unregistering hci device when usb disconnect. Removing BT usb dongle without properly releasing the interface may cause Kernel panic while unregister hci device. Signed-off-by: Chris Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Change conditions for Bluetooth driver claiming and releasing usb ISO interface for MediaTek ISO data transmission. Signed-off-by: Chris Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Firmwares are already in upstream. kernel boot log as following: Bluetooth: hci0: using rampatch file: qca/rampatch_usb_00190200.bin Bluetooth: hci0: QCA: patch rome 0x190200 build 0x5656, firmware rome 0x190200 build 0x43fb Bluetooth: hci0: using NVM file: qca/nvm_usb_00190200.bin Paired BT headphone, output is good. T: Bus=01 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0fc Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Aaron Ma <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add one more part with ID (0x0489, 0xe0f3) to usb_device_id table for Qualcomm WCN785x, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=01 Prnt=01 Port=13 Cnt=03 Dev#= 4 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e0f3 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add one more part with ID (0x13d3, 0x3623) to usb_device_id table for Qualcomm WCN785x, and its device info from /sys/kernel/debug/usb/devices is shown below: T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3623 Rev= 0.01 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I: If#= 1 Alt= 7 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 65 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 65 Ivl=1ms Signed-off-by: Zijun Hu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This updates all FW names by dropping the _v0 suffix. Its been decided that all NXP BT/ WiFi FW names won't support _v0 suffix. The suffix would be kept for next HW versions such as v1, v2 and so on, which do not have backward compatible FW. This change affects W8987, IW416 and IW615 chipsets, out of which new FW files for W8987 and IW615 are yet to be released to broad market. For IW416, old and new FW names are added to maintain backward compatibility for existing customers. Signed-off-by: Neeraj Sanjay Kale <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This changes the chip name of IW615 to IW610. IW610 (formerly called IW615) is yet to be released to broad market, hence there is no issue of backward compatibility. Signed-off-by: Neeraj Sanjay Kale <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
An hci_conn_drop() call was immediately used after a null pointer check for an hci_conn_link() call in two function implementations. Thus call such a function only once instead directly before the checks. This issue was transformed by using the Coccinelle software. Signed-off-by: Markus Elfring <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Correctly spelled comments make it easier for the reader to understand the code. Fix typos: 'fragement' ==> 'fragment', 'genration' ==> 'generation', 'funciton' ==> 'function', 'Explitly' ==> 'Explicitly', 'explaination' ==> 'explanation', 'Tranlate' ==> 'Translate', 'immediatelly' ==> 'immediately', 'isntance' ==> 'instance', 'transmittion' ==> 'transmission', 'recevie' ==> 'receive', 'outselves' ==> 'ourselves', 'conrol' ==> 'control'. Signed-off-by: Yan Zhen <[email protected]> Reviewed-by: AngeloGioacchino Del Regno <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add the support ID 0489:e123 to usb_device_id table for Realtek RTL8852B chip. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=01 Lev=01 Prnt=01 Port=07 Cnt=04 Dev#= 7 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e123 Rev= 0.00 S: Manufacturer=Realtek S: Product=Bluetooth Radio S: SerialNumber=00e04c000001 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms Signed-off-by: Hilda Wu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add HW IDs for wireless module. These HW IDs are extracted from Windows driver inf file and the test for card bring up successful. MT7920 HW IDs test with below patch. https://patchwork.kernel.org/project/bluetooth/ patch/[email protected]/ Patch has been tested successfully and controller is recognized devices pair successfully. MT7920 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x008a008a, Build Time: 20240930111457 Bluetooth: hci0: Device setup in 143004 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: hci0: AOSP quality report is supported Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 MT7925 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20240816133202 Bluetooth: hci0: Device setup in 286558 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Signed-off-by: Jiande Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This makes use of disable_delayed_work_sync instead cancel_delayed_work_sync as it not only cancel the ongoing work but also disables new submit which is disarable since the object holding the work is about to be freed. Reported-by: [email protected] Tested-by: [email protected] Closes: https://syzkaller.appspot.com/bug?extid=2446dd3cb07277388db6 Signed-off-by: Luiz Augusto von Dentz <[email protected]>
If bt_debugfs is not created successfully, which happens if either
CONFIG_DEBUG_FS or CONFIG_DEBUG_FS_ALLOW_ALL is unset, then iso_init()
returns early and does not set iso_inited to true. This means that a
subsequent call to iso_init() will result in duplicate calls to
proto_register(), bt_sock_register(), etc.
With CONFIG_LIST_HARDENED and CONFIG_BUG_ON_DATA_CORRUPTION enabled, the
duplicate call to proto_register() triggers this BUG():
list_add double add: new=ffffffffc0b280d0, prev=ffffffffbab56250,
next=ffffffffc0b280d0.
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:35!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 2 PID: 887 Comm: bluetoothd Not tainted 6.10.11-1-ao-desktop #1
RIP: 0010:__list_add_valid_or_report+0x9a/0xa0
...
__list_add_valid_or_report+0x9a/0xa0
proto_register+0x2b5/0x340
iso_init+0x23/0x150 [bluetooth]
set_iso_socket_func+0x68/0x1b0 [bluetooth]
kmem_cache_free+0x308/0x330
hci_sock_sendmsg+0x990/0x9e0 [bluetooth]
__sock_sendmsg+0x7b/0x80
sock_write_iter+0x9a/0x110
do_iter_readv_writev+0x11d/0x220
vfs_writev+0x180/0x3e0
do_writev+0xca/0x100
...
This change removes the early return. The check for iso_debugfs being
NULL was unnecessary, it is always NULL when iso_inited is false.
Cc: [email protected]
Fixes: ccf74f2 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Aaron Thompson <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
If iso_init() has been called, iso_exit() must be called on module
unload. Without that, the struct proto that iso_init() registered with
proto_register() becomes invalid, which could cause unpredictable
problems later. In my case, with CONFIG_LIST_HARDENED and
CONFIG_BUG_ON_DATA_CORRUPTION enabled, loading the module again usually
triggers this BUG():
list_add corruption. next->prev should be prev (ffffffffb5355fd0),
but was 0000000000000068. (next=ffffffffc0a010d0).
------------[ cut here ]------------
kernel BUG at lib/list_debug.c:29!
Oops: invalid opcode: 0000 [#1] PREEMPT SMP PTI
CPU: 1 PID: 4159 Comm: modprobe Not tainted 6.10.11-4+bt2-ao-desktop #1
RIP: 0010:__list_add_valid_or_report+0x61/0xa0
...
__list_add_valid_or_report+0x61/0xa0
proto_register+0x299/0x320
hci_sock_init+0x16/0xc0 [bluetooth]
bt_init+0x68/0xd0 [bluetooth]
__pfx_bt_init+0x10/0x10 [bluetooth]
do_one_initcall+0x80/0x2f0
do_init_module+0x8b/0x230
__do_sys_init_module+0x15f/0x190
do_syscall_64+0x68/0x110
...
Cc: [email protected]
Fixes: ccf74f2 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Aaron Thompson <[email protected]>
Signed-off-by: Luiz Augusto von Dentz <[email protected]>
If bt_init() fails, the debugfs directory currently is not removed. If the module is loaded again after that, the debugfs directory is not set up properly due to the existing directory. # modprobe bluetooth # ls -laF /sys/kernel/debug/bluetooth total 0 drwxr-xr-x 2 root root 0 Sep 27 14:26 ./ drwx------ 31 root root 0 Sep 27 14:25 ../ -r--r--r-- 1 root root 0 Sep 27 14:26 l2cap -r--r--r-- 1 root root 0 Sep 27 14:26 sco # modprobe -r bluetooth # ls -laF /sys/kernel/debug/bluetooth ls: cannot access '/sys/kernel/debug/bluetooth': No such file or directory # # modprobe bluetooth modprobe: ERROR: could not insert 'bluetooth': Invalid argument # dmesg | tail -n 6 Bluetooth: Core ver 2.22 NET: Registered PF_BLUETOOTH protocol family Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: Faking l2cap_init() failure for testing NET: Unregistered PF_BLUETOOTH protocol family # ls -laF /sys/kernel/debug/bluetooth total 0 drwxr-xr-x 2 root root 0 Sep 27 14:31 ./ drwx------ 31 root root 0 Sep 27 14:26 ../ # # modprobe bluetooth # dmesg | tail -n 7 Bluetooth: Core ver 2.22 debugfs: Directory 'bluetooth' with parent '/' already present! NET: Registered PF_BLUETOOTH protocol family Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized # ls -laF /sys/kernel/debug/bluetooth total 0 drwxr-xr-x 2 root root 0 Sep 27 14:31 ./ drwx------ 31 root root 0 Sep 27 14:26 ../ # Cc: [email protected] Fixes: ffcecac ("Bluetooth: Create root debugfs directory during module init") Signed-off-by: Aaron Thompson <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
…using GPIO This adds a new optional device tree property device-wakeup-gpios, which specifies the GPIO connected to BT_WAKE_IN pin of the NXP chipset. If this property is defined, the driver will use this GPIO for driving chip into sleep/wakeup state, else use the UART break signal by default. Signed-off-by: Neeraj Sanjay Kale <[email protected]> Reviewed-by: Rob Herring (Arm) <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This adds support for driving the chip into sleep or wakeup with a GPIO. If the device tree property device-wakeup-gpios is defined, the driver utilizes this GPIO for controlling the chip's power save state, else it uses the default UART-break method. Signed-off-by: Neeraj Sanjay Kale <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This fixes not checking if skb really contains an ACL header otherwise the code may attempt to access some uninitilized/invalid memory past the valid skb->data. Reported-by: [email protected] Tested-by: [email protected] Closes: https://syzkaller.appspot.com/bug?extid=6ea290ba76d8c1eb1ac2 Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This fixes not checking if skb really contains an SCO header otherwise the code may attempt to access some uninitilized/invalid memory past the valid skb->data. Signed-off-by: Luiz Augusto von Dentz <[email protected]>
The following handshake mechanism needs be followed after firmware download is completed to bring the firmware to running state. After firmware fragments of Operational image are downloaded and secure sends result of the image succeeds, 1. Driver sends HCI Intel reset with boot option #1 to switch FW image. 2. FW sends Alive GP[0] MSIx 3. Driver enables data path (doorbell 0x460 for RBDs, etc...) 4. Driver gets Bootup event from firmware 5. Driver performs D0 entry to device (WRITE to IPC_Sleep_Control =0x0) 6. FW sends Alive GP[0] MSIx 7. Device host interface is fully set for BT protocol stack operation. 8. Driver may optionally get debug event with ID 0x97 which can be dropped For Intermediate loadger image, all the above steps are applicable expcept #5 and #6. On HCI_OP_RESET, firmware raises alive interrupt. Driver needs to wait for it before passing control over to bluetooth stack. Co-developed-by: Devegowda Chandrashekar <[email protected]> Signed-off-by: Devegowda Chandrashekar <[email protected]> Signed-off-by: Kiran K <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This patch adds a recovery mechanism to recover controller if firmware download fails due to unresponsive controller, command timeout, firmware signature verification failure etc. Driver attmepts maximum of 5 times before giving up. Signed-off-by: Kiran K <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
If the device tree is properly written, the SDIO function device node should be correctly defined, and the mmc core in Linux should correctly tie it to the device being probed. Only fall back to searching for the device node by compatible if the original device node tied to the device is incorrect, as seen in older device trees. Signed-off-by: Chen-Yu Tsai <[email protected]> Tested-by: AngeloGioacchino Del Regno <[email protected]> # Reviewed-by: AngeloGioacchino Del Regno <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This partially reverts 81b3e33 ("Bluetooth: btusb: Don't fail external suspend requests") as it introduced a call to hci_suspend_dev that assumes the system-suspend which doesn't work well when just the device is being suspended because wakeup flag is only set for remote devices that can wakeup the system. Reported-by: Rafael J. Wysocki <[email protected]> Reported-by: Heiner Kallweit <[email protected]> Reported-by: Kenneth Crudup <[email protected]> Fixes: 6107122 ("Bluetooth: btusb: Don't fail external suspend requests") Signed-off-by: Luiz Augusto von Dentz <[email protected]> Tested-by: Rafael J. Wysocki <[email protected]>
There's issue as follows: KASAN: maybe wild-memory-access in range [0xdead...108-0xdead...10f] CPU: 3 UID: 0 PID: 2805 Comm: rmmod Tainted: G W RIP: 0010:proto_unregister+0xee/0x400 Call Trace: <TASK> __do_sys_delete_module+0x318/0x580 do_syscall_64+0xc1/0x1d0 entry_SYSCALL_64_after_hwframe+0x77/0x7f As bnep_init() ignore bnep_sock_init()'s return value, and bnep_sock_init() will cleanup all resource. Then when remove bnep module will call bnep_sock_cleanup() to cleanup sock's resource. To solve above issue just return bnep_sock_init()'s return value in bnep_exit(). Fixes: 1da177e ("Linux-2.6.12-rc2") Signed-off-by: Ye Bin <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add DSBR support for BlazarIW, BlazarU and Gale Peak2 cores. Refer commit eb9e749 ("Bluetooth: btintel: Allow configuring drive strength of BRI") for details about DSBR. Signed-off-by: Kiran K <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Use the new devm_clk_get_optional_enabled_with_rate() clock helper to shrink the code a bit. Signed-off-by: Bartosz Golaszewski <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Fake CSR controllers don't seem to handle short-transfer properly which cause command to time out: kernel: usb 1-1: new full-speed USB device number 19 using xhci_hcd kernel: usb 1-1: New USB device found, idVendor=0a12, idProduct=0001, bcdDevice=88.91 kernel: usb 1-1: New USB device strings: Mfr=0, Product=2, SerialNumber=0 kernel: usb 1-1: Product: BT DONGLE10 ... Bluetooth: hci1: Opcode 0x1004 failed: -110 kernel: Bluetooth: hci1: command 0x1004 tx timeout According to USB Spec 2.0 Section 5.7.3 Interrupt Transfer Packet Size Constraints a interrupt transfer is considered complete when the size is 0 (ZPL) or < wMaxPacketSize: 'When an interrupt transfer involves more data than can fit in one data payload of the currently established maximum size, all data payloads are required to be maximum-sized except for the last data payload, which will contain the remaining data. An interrupt transfer is complete when the endpoint does one of the following: • Has transferred exactly the amount of data expected • Transfers a packet with a payload size less than wMaxPacketSize or transfers a zero-length packet' Link: https://bugzilla.kernel.org/show_bug.cgi?id=219365 Fixes: 7b05933 ("Bluetooth: btusb: Fix not handling ZPL/short-transfer") Signed-off-by: Luiz Augusto von Dentz <[email protected]>
The switch case statement has a default branch. Thus, the return statement at the end of the function can never be reached. Fix it by removing the return statement at the end of the function. This issue was reported by Coverity Scan. Signed-off-by: Everest K.C. <[email protected]> Reviewed-by: Shuah Khan <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
conn->sk maybe have been unlinked/freed while waiting for iso_conn_lock so this checks if the conn->sk is still valid by checking if it part of iso_sk_list. Fixes: ccf74f2 ("Bluetooth: Add BTPROTO_ISO socket type") Signed-off-by: Luiz Augusto von Dentz <[email protected]>
pcim_iomap_regions() and pcim_iomap_table() have been deprecated in commit e354bb8 ("PCI: Deprecate pcim_iomap_table(), pcim_iomap_regions_request_all()"). Replace these functions with pcim_iomap_region(). Signed-off-by: Philipp Stanner <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
MediaTek iso data anchor init should be moved to where MediaTek claims iso data interface. If there is an unexpected BT usb disconnect during setup flow, it will cause a NULL pointer crash issue when releasing iso anchor since the anchor wasn't been init yet. Adjust the position to do iso data anchor init. [ 17.137991] pc : usb_kill_anchored_urbs+0x60/0x168 [ 17.137998] lr : usb_kill_anchored_urbs+0x44/0x168 [ 17.137999] sp : ffffffc0890cb5f0 [ 17.138000] x29: ffffffc0890cb5f0 x28: ffffff80bb6c2e80 [ 17.144081] gpio gpiochip0: registered chardev handle for 1 lines [ 17.148421] x27: 0000000000000000 [ 17.148422] x26: ffffffd301ff4298 x25: 0000000000000003 x24: 00000000000000f0 [ 17.148424] x23: 0000000000000000 x22: 00000000ffffffff x21: 0000000000000001 [ 17.148425] x20: ffffffffffffffd8 x19: ffffff80c0f25560 x18: 0000000000000000 [ 17.148427] x17: ffffffd33864e408 x16: ffffffd33808f7c8 x15: 0000000000200000 [ 17.232789] x14: e0cd73cf80ffffff x13: 50f2137c0a0338c9 x12: 0000000000000001 [ 17.239912] x11: 0000000080150011 x10: 0000000000000002 x9 : 0000000000000001 [ 17.247035] x8 : 0000000000000000 x7 : 0000000000008080 x6 : 8080000000000000 [ 17.254158] x5 : ffffffd33808ebc0 x4 : fffffffe033dcf20 x3 : 0000000080150011 [ 17.261281] x2 : ffffff8087a91400 x1 : 0000000000000000 x0 : ffffff80c0f25588 [ 17.268404] Call trace: [ 17.270841] usb_kill_anchored_urbs+0x60/0x168 [ 17.275274] btusb_mtk_release_iso_intf+0x2c/0xd8 [btusb (HASH:5afe 6)] [ 17.284226] btusb_mtk_disconnect+0x14/0x28 [btusb (HASH:5afe 6)] [ 17.292652] btusb_disconnect+0x70/0x140 [btusb (HASH:5afe 6)] [ 17.300818] usb_unbind_interface+0xc4/0x240 [ 17.305079] device_release_driver_internal+0x18c/0x258 [ 17.310296] device_release_driver+0x1c/0x30 [ 17.314557] bus_remove_device+0x140/0x160 [ 17.318643] device_del+0x1c0/0x330 [ 17.322121] usb_disable_device+0x80/0x180 [ 17.326207] usb_disconnect+0xec/0x300 [ 17.329948] hub_quiesce+0x80/0xd0 [ 17.333339] hub_disconnect+0x44/0x190 [ 17.337078] usb_unbind_interface+0xc4/0x240 [ 17.341337] device_release_driver_internal+0x18c/0x258 [ 17.346551] device_release_driver+0x1c/0x30 [ 17.350810] usb_driver_release_interface+0x70/0x88 [ 17.355677] proc_ioctl+0x13c/0x228 [ 17.359157] proc_ioctl_default+0x50/0x80 [ 17.363155] usbdev_ioctl+0x830/0xd08 [ 17.366808] __arm64_sys_ioctl+0x94/0xd0 [ 17.370723] invoke_syscall+0x6c/0xf8 [ 17.374377] el0_svc_common+0x84/0xe0 [ 17.378030] do_el0_svc+0x20/0x30 [ 17.381334] el0_svc+0x34/0x60 [ 17.384382] el0t_64_sync_handler+0x88/0xf0 [ 17.388554] el0t_64_sync+0x180/0x188 [ 17.392208] Code: f9400677 f100a2f4 54fffea0 d503201f (b8350288) [ 17.398289] ---[ end trace 0000000000000000 ]--- Fixes: ceac1cb ("Bluetooth: btusb: mediatek: add ISO data transmission functions") Signed-off-by: Chris Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Fix __hci_cmd_sync_sk() to return not NULL for unknown opcodes. __hci_cmd_sync_sk() returns NULL if a command returns a status event. However, it also returns NULL where an opcode doesn't exist in the hci_cc table because hci_cmd_complete_evt() assumes status = skb->data[0] for unknown opcodes. This leads to null-ptr-deref in cmd_sync for HCI_OP_READ_LOCAL_CODECS as there is no hci_cc for HCI_OP_READ_LOCAL_CODECS, which always assumes status = skb->data[0]. KASAN: null-ptr-deref in range [0x0000000000000070-0x0000000000000077] CPU: 1 PID: 2000 Comm: kworker/u9:5 Not tainted 6.9.0-ga6bcb805883c-dirty #10 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.15.0-1 04/01/2014 Workqueue: hci7 hci_power_on RIP: 0010:hci_read_supported_codecs+0xb9/0x870 net/bluetooth/hci_codec.c:138 Code: 08 48 89 ef e8 b8 c1 8f fd 48 8b 75 00 e9 96 00 00 00 49 89 c6 48 ba 00 00 00 00 00 fc ff df 4c 8d 60 70 4c 89 e3 48 c1 eb 03 <0f> b6 04 13 84 c0 0f 85 82 06 00 00 41 83 3c 24 02 77 0a e8 bf 78 RSP: 0018:ffff888120bafac8 EFLAGS: 00010212 RAX: 0000000000000000 RBX: 000000000000000e RCX: ffff8881173f0040 RDX: dffffc0000000000 RSI: ffffffffa58496c0 RDI: ffff88810b9ad1e4 RBP: ffff88810b9ac000 R08: ffffffffa77882a7 R09: 1ffffffff4ef1054 R10: dffffc0000000000 R11: fffffbfff4ef1055 R12: 0000000000000070 R13: 0000000000000000 R14: 0000000000000000 R15: ffff88810b9ac000 FS: 0000000000000000(0000) GS:ffff8881f6c00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00007f6ddaa3439e CR3: 0000000139764003 CR4: 0000000000770ef0 PKRU: 55555554 Call Trace: <TASK> hci_read_local_codecs_sync net/bluetooth/hci_sync.c:4546 [inline] hci_init_stage_sync net/bluetooth/hci_sync.c:3441 [inline] hci_init4_sync net/bluetooth/hci_sync.c:4706 [inline] hci_init_sync net/bluetooth/hci_sync.c:4742 [inline] hci_dev_init_sync net/bluetooth/hci_sync.c:4912 [inline] hci_dev_open_sync+0x19a9/0x2d30 net/bluetooth/hci_sync.c:4994 hci_dev_do_open net/bluetooth/hci_core.c:483 [inline] hci_power_on+0x11e/0x560 net/bluetooth/hci_core.c:1015 process_one_work kernel/workqueue.c:3267 [inline] process_scheduled_works+0x8ef/0x14f0 kernel/workqueue.c:3348 worker_thread+0x91f/0xe50 kernel/workqueue.c:3429 kthread+0x2cb/0x360 kernel/kthread.c:388 ret_from_fork+0x4d/0x80 arch/x86/kernel/process.c:147 ret_from_fork_asm+0x1a/0x30 arch/x86/entry/entry_64.S:244 Fixes: abfeea4 ("Bluetooth: hci_sync: Convert MGMT_OP_START_DISCOVERY") Signed-off-by: Sungwoo Kim <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add VID 0489 & PID e111 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=02 Lev=02 Prnt=02 Port=04 Cnt=02 Dev#= 4 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e111 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Hao Qin <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
of_find_node_by_path() returns a pointer to a device_node with its refcount incremented, and a call to of_node_put() is required to decrement the refcount again and avoid leaking the resource. If 'of_property_read_string_index(root, "compatible", 0, &tmp)' fails, the function returns without calling of_node_put(root) before doing so. The automatic cleanup attribute can be used by means of the __free() macro to automatically call of_node_put() when the variable goes out of scope, fixing the issue and also accounting for new error paths. Fixes: 63fac33 ("Bluetooth: btbcm: Support per-board firmware variants") Signed-off-by: Javier Carrasco <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
The original timeout setting for HCI Reset on shutdown is 10 seconds. HCI Reset shouldn't take 10 seconds to complete so instead use the default timeout for commands. Signed-off-by: Hilda Wu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
The Bluetooth Core spec does not allow a LE PA Create sync command to be sent to Controller if another one is pending (Vol 4, Part E, page 2493). In order to avoid this issue, the HCI_CONN_CREATE_PA_SYNC was added to mark that the LE PA Create Sync command has been sent for a hcon. Once the PA Sync Established event is received, the hcon flag is erased and the next pending hcon is handled. Signed-off-by: Iulia Tanasescu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Currently, when a BIS slave connection is notified to the ISO layer, the parent socket is tried to be matched by the HCI_EVT_LE_BIG_SYNC_ESTABILISHED event. However, a BIS slave connection is notified to the ISO layer after the Command Complete for the LE Setup ISO Data Path command is received. This causes the parent to be incorrectly matched if multiple listen sockets are present. This commit adds a fix by matching the parent based on the BIG handle set in the notified connection. Signed-off-by: Iulia Tanasescu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
The Bluetooth Core spec does not allow a LE BIG Create sync command to be sent to Controller if another one is pending (Vol 4, Part E, page 2586). In order to avoid this issue, the HCI_CONN_CREATE_BIG_SYNC was added to mark that the LE BIG Create Sync command has been sent for a hcon. Once the BIG Sync Established event is received, the hcon flag is erased and the next pending hcon is handled. Signed-off-by: Iulia Tanasescu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Currently, hci_conn_hash_lookup_big only checks for BIS master connections, by filtering out connections with the destination address set. This commit updates this function to also consider BIS slave connections, since it is also used for a Broadcast Receiver to set an available BIG handle before issuing the LE BIG Create Sync command. Signed-off-by: Iulia Tanasescu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add VID 0489 & PID e124 for MediaTek MT7925 USB Bluetooth chip. The information in /sys/kernel/debug/usb/devices about the Bluetooth device is listed as the below. T: Bus=01 Lev=01 Prnt=01 Port=08 Cnt=02 Dev#= 3 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e124 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Signed-off-by: Jonathan McCrohan <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Add below HWIDs for MediaTek MT7925 USB Bluetooth chip. VID 0x0489, PID 0xe14f VID 0x0489, PID 0xe150 VID 0x0489, PID 0xe151 Patch has been tested successfully and controller is recognized device pair successfully. MT7925 module bring up message as below. Bluetooth: Core ver 2.22 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized Bluetooth: hci0: HW/SW Version: 0x00000000, Build Time: 20240816133202 Bluetooth: hci0: Device setup in 286558 usecs Bluetooth: hci0: HCI Enhanced Setup Synchronous Connection command is advertised, but not supported. Bluetooth: hci0: AOSP extensions version v1.00 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized Bluetooth: MGMT ver 1.22 Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Signed-off-by: Jiande Lu <[email protected]> Signed-off-by: Luiz Augusto von Dentz <[email protected]>
Zephyr(1) has been using the same bus defines as Linux so tools likes of btmon, etc, are able to decode the bus used by the driver to transport HCI packets. Link: zephyrproject-rtos/zephyr#80808 Signed-off-by: Luiz Augusto von Dentz <[email protected]>
This patch adds workflow files for ci: [schedule_work.yml] - The workflow file for scheduled work - Sync the repo with upstream repo and rebase the workflow branch - Review the patches in the patchwork and creates the PR if needed [ci.yml] - The workflow file for CI tasks - Run CI tests when PR is created
Add compatibility Bluetooth device MT7925 for Asus UM5606 with ID 13d3:3608. The device info from /sys/kernel/debug/usb/devices as below. T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=13d3 ProdID=3608 Rev= 1.00 S: Manufacturer=MediaTek Inc. S: Product=Wireless_Device S: SerialNumber=000000000 C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none) E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us Tested in Asus Zenbook S 16 UM5606XA Co-developed-by: Félix Jara <[email protected]> Signed-off-by: Félix Jara <[email protected]> Tested-by: Félix Jara <[email protected]> Link: openSUSE/kernel#10 Signed-off-by: WangYuli <[email protected]>
github-actions
bot
force-pushed
the
workflow
branch
5 times, most recently
from
49d03d5 to
5d30777
Compare
github-actions
bot
force-pushed
the
workflow
branch
2 times, most recently
from
a46cce6 to
e776968
Compare
github-actions
bot
force-pushed
the
workflow
branch
3 times, most recently
from
e8e1f61 to
3a2cebb
Compare
github-actions
bot
force-pushed
the
workflow
branch
2 times, most recently
from
10e76e2 to
c8aff3f
Compare
Sign up for free
to join this conversation on GitHub.
Already have an account?
Sign in to comment
Add this suggestion to a batch that can be applied as a single commit.
This suggestion is invalid because no changes were made to the code.
Suggestions cannot be applied while the pull request is closed.
Suggestions cannot be applied while viewing a subset of changes.
Only one suggestion per line can be applied in a batch.
Add this suggestion to a batch that can be applied as a single commit.
Applying suggestions on deleted lines is not supported.
You must change the existing code in this line in order to create a valid suggestion.
Outdated suggestions cannot be applied.
This suggestion has been applied or marked resolved.
Suggestions cannot be applied from pending reviews.
Suggestions cannot be applied on multi-line comments.
Suggestions cannot be applied while the pull request is queued to merge.
Suggestion cannot be applied right now. Please check back later.
From: Félix Jara [email protected]
Add compatibility Bluetooth device MT7925 for Asus UM5606 with
ID 13d3:3608.
The device info from /sys/kernel/debug/usb/devices as below.
T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=480 MxCh= 0
D: Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=13d3 ProdID=3608 Rev= 1.00
S: Manufacturer=MediaTek Inc.
S: Product=Wireless_Device
S: SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A: FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=125us
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 64 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 64 Ivl=125us
I: If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E: Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E: Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Tested in Asus Zenbook S 16 UM5606XA
Co-developed-by: Félix Jara [email protected]
Signed-off-by: Félix Jara [email protected]
Tested-by: Félix Jara [email protected]
Link: openSUSE/kernel#10
Signed-off-by: WangYuli [email protected]
drivers/bluetooth/btusb.c | 5 +++++
1 file changed, 5 insertions(+)