AstroLive

Connector for the ASCOM Alpaca REST API designed to work with Home Assistant via MQTT.

The integration with Home Assistant is implemented via MQTT for sensor and camera entities and supports autodiscovery of Home Assistant for the devices.

AstroLive uses the nice ALPACA client implementation of the OCA Box classes which is used by the Araucaria Project.

Table of Content

How It Works
Breaking Changes when upgrading from Version 0.3
Requirements
My Personal Setup
Usage
Integrate with Home Assistant
- Devices and Sensors, Binary Sensors, Switches and Cameras
- Sending Commands
  - Input Texts
  - Scripts

How It Works

AstroLive connects via the ASCOM Alpaca API to your observatory.
For each configured and connected component a MQTT device configuration for sensors, binary_sensors, switches and if applicable camera is created below homeassistant/.
As of now the following components are supported:
- Telescope
- Camera
- Camera via File
- Focuser
- Switch
- FilterWheel
- Dome
- Rotator
- SafetyMonitor
These configurations allow MQTT auto discovery in Home Assistant.
AstroLive then starts a seperate thread for each device which queries the compenent status interval according to the configuration and publishes the device state to MQTT.
If the component is of the type Camera the last captured FITS image is autostretched, downsized and published as a .jpg. This is the same for Camera via file where AstroLive watches a directory for new FITS images.

Slewing the telescope using the equatorial coordinate system, parking and unparking the scope, moving the focuser and some more commands are possible directly from Home Assistant.

AstroLive is designed to run as a container to be deployed on a dedicated host or next to Home Assistant. It does not require any custom integration for Home Assistant since communication is solely via MQTT.

Breaking Changes when upgrading from Version 0.3

With version 0.3 AstroLive did only use Home Assistant sensors and camera entities. This simplified the initial implementations but using a sensor might not always be the appropriate entity type. An on/off switch in the Pegasus UPB2 should either be represented as a binary_sensor or even better as an actual switch.

For this reason some of the entities in your Home Assistant will automatically change from sensor to switch or binary_sensor when using AstroLive 0.4+. This likely results in missing entities in your Lovelace configuration or automations which should easily be fixed by changing the type there as well.

See chapter Devices and Sensors, Binary Sensors, Switches and Cameras for details.

Requirements

A windows (mini) pc/notebook controlling your scope
ASCOM Platform
ASCOMRemote.
Container runtime engine (e.g. Docker).
MQTT Broker (e.g. Mosquitto).
A recent version of Home Assistant with MQTT autodiscovery enabled.

My Personal Setup

To give you an idea how I did setup my observatory together with AstroLive and AstroWeather here's my setup:

Hardware
- Telescopes: Skywatcher Esprit 120ED, William Optics AP 71
- Mounts: Skywatcher EQ6-R, iOptron GEM45
- Camera: QHY268c
- Guide Camera: QHY5III462c
- Off Axis Guider: OAG-M
- Filter Wheel: QHY CFW3M-US
- Switch: PegasusAstro Ultimate Powerbox v2
- Focuser: PegasusAstro Focus Cube, ZWO EAF
- Mini PC: MeLE Quieter2 8GB 256GB Windows 11
Software:
- NINA, PHD2, ASCOM Platform, EQASCOM, QHYCCD Win AllInOne, Polemaster, iPolar, PegasusAstro Unity, Dropbox, HASS.Agent, Libre Hardware Monitor

All off the software is running on the MeLE Quieter2 mini pc which I mounted on top of the scope. I configured NINA to store image files within a dedicated directory which is synced by Dropbox. This directory is then monitored by AstroLive to enable the image processing.

Since NINA does provide it's own drivers to interact with the QHY camera I did not connect the cameras to ASCOMRemote. During my tests with AstroLive I encountered problems while imaging if AstroLive uses the Camera API of ASCOMRemote. I need to investigate this further, but processing the resulting image stored on disk is working nicely for me and lowers the load on the mini pc anyways.

Usage

Ensure to have the ASCOM Platform deployed on your astro imaging server.

Installation and Configuration of ASCOM Remote Server

Download and install the latest version from here: ASCOMRemote

Show instructions

Add the devices you want to use in conjunction of AstroLive. The following screenshot show a connected Focuser, Telescope and Switch.

You need to press [Setup] for each configured device to connect it to the ASCOM Remote Server Configuration.

Set a name for the servers location (e.g. Backyard) and specify the Server IP Address. This is the IP the Remote Server is running on. Choose a port (default is 11111) and leave the rest to the defaults.

Press [OK]

Links:

Get and Configure AstroLive

Clone AstroLive

git clone https://github.com/mawinkler/astrolive

Now, create a default.cfg.yaml based on the supplied default.cfg.yaml.sample and modify it to your needs. The yaml should be pretty self explanatory :-)

cp astrolive/default.cfg.yaml.sample astrolive/default.cfg.yaml

Note: If you are using drivers provided with the sequencer software, using ASCOM remote in parallel will mess up the imaging session when accessing the camera API. Tested with QHY and N.I.N.A./PHD2. For that reason, I'm always using the camera_file component witch checks for the latest FITS-file published within a given directory tree.

Show YAML

default:
  include: backyard

backyard:
  observatory:
    # Name of the observatory
    comment: Backyard Scope
    # Longitude
    lon: <LONGITUDE>
    # Lattitude
    lat: <LATTITUDE>
    # Elevation
    elev: <ELEVATION>
    # Communication protocol
    protocol: alpaca
    # Address of the ASCOM Remote server
    address: http://<IP OF ASCOMRemote>:11111/api/v1

    components:
      telescope:
        # Kind of the device
        kind: telescope
        comment: <NAME OF YOUR SCOPE>
        # Device number as configured in ASCOM Remote
        device_number: 0
        # Name prefix of the created sensor in MQTT
        friendly_name: <NAME OF YOUR SCOPE>
        # Update interval in seconds
        update_interval: 15
        # List of components belonging to the telescope
        components:
          # Note to ASCOM:
          # If you are using drivers provided with the sequencer software,
          # using ASCOM remote in parallel will mess up the imaging session.
          # Tested with QHY and N.I.N.A./PHD2.
          
          # Valid device kinds are
          #   telescope: Telescope
          #   dome: Dome
          #   camera: Camera
          #   filterwheel: Filter Wheel
          #   focuser: Focuser
          #   rotator: Rotator
          #   switch: Switch
          #   safetymonitor: SafetyMonitor
          #   camera_file: Camera File, reads and processes the latest image within
          #     from a configured location.

          # camera:
          #   # Kind of the device
          #   kind: camera
          #   # Device number as configured in ASCOM Remote
          #   device_number: 0
          #   # Name prefix of the created sensor in MQTT
          #   friendly_name: <NAME OF YOUR IMAGING CAMERA>
          #   # Get image via ASCOM remote. If false, process sensors only
          #   image: true
          #   # Update interval in seconds
          #   update_interval: 60

          # guiding_camera:
          #   kind: camera
          #   device_number: 1
          #   friendly_name: <NAME OF YOUR GUIDING CAMERA>
          #   image: true
          #   update_interval: 60

          camera_file:
            kind: file
            friendly_name: <NAME OF YOUR IMAGING CAMERA>
            # Monitoring directory for new image files
            # Only FITS files are supported
            monitor: '/fits'
            update_interval: 60

          focuser:
            kind: focuser
            friendly_name: <NAME OF YOUR FOCUSER>
            update_interval: 15

          switch:
            kind: switch
            friendly_name: <NAME OF YOUR SWITCH>
            update_interval: 30
            # Optionally define the number of available switches.
            # If not set astrolive will query the switch which is NOT
            # supported with all ASCOM drivers.
            # max_switch: 8
            
          filterwheel:
            kind: filterwheel
            friendly_name: <NAME OF YOUR FILTERWHEEL>
            update_interval: 15

          dome:
            kind: dome
            friendly_name: <NAME OF YOUR DOME>
            update_interval: 30
          
          safetymonitor:
            kind: safetymonitor
            friendly_name: <NAME OF YOUR SAFETYMONITOR>
            update_interval: 30

          rotator:
            kind: rotator
            friendly_name: <NAME OF YOUR ROTATOR>
            update_interval: 30

    # MQTT configuration
    mqtt:
      # Address of the MQTT broker
      broker: <IP OF YOUR BROKER>
      # Listen port of the MQTT broker
      # defaut 1883 or 8883 for tls
      port: 1883
      # Client name for astrolive
      client: astrolive
      # Username
      username: ''
      # Password
      password: ''
      # TLS insecure
      tls:
        enabled: False
        insecure: True
        # The certification authority certificate which signed the MQTT server certicate
        ca: /certs/ca.crt

Run

AstroLive checks recursively within the configured directory for new FITS files if you configured camera_file. By default it checks within the directory /fits.

If you want to use TLS for the connection to the MQTT broker you need to provide the certificate of the certification authority which signed the MQTT server certificate (defaults to /certs/ca.crt).

Run with Python

Ensure to have the dependencies installed

pip3 install -r requirements.txt

Start AstroLive

python3 run.py

Build & Run as a container

This is the way :-).

| [T]  
| | |√  <••>  
| ( )   (  )

Build

docker build --tag astrolive .

Run

# As a container
docker run \
  --volume /fits:/fits:ro \
  --name astrolive \
  --rm \
  astrolive

# As a detached container
docker run \
  --volume /fits:/fits:ro \
  --name astrolive \
  --rm -d \
  astrolive

Docker-compose example:

version: "3.2"
services:
  astrolive:
    image: astrolive:latest
    container_name: astrolive
    depends_on:
      - mqtt
    environment:
      - TZ=Europe/Berlin
    volumes:
      - /astrolive/backyard.cfg.yaml:/app/astrolive/default.cfg.yaml
      - /fits:/fits:ro
    restart: always

If using TLS

# As a container
docker run \
  --volume /fits:/fits:ro \
  --volume /certs:/certs:ro \
  --name astrolive \
  --rm \
  astrolive

# As a detached container
docker run \
  --volume /fits:/fits:ro \
  --volume /certs:/certs:ro \
  --name astrolive \
  --rm -d \
  astrolive

Docker-compose example:

version: "3.2"
services:
  astrolive:
    image: astrolive:latest
    container_name: astrolive
    depends_on:
      - mqtt
    environment:
      - TZ=Europe/Berlin
    volumes:
      - /astrolive/backyard.cfg.yaml:/app/astrolive/default.cfg.yaml
      - /fits:/fits:ro
      - /certs:/certs:ro
    restart: always

Integrate with Home Assistant

Effectively, there is no configuration required if you just want to monitor your observatory. Simply creating your Lovelace UI using the generated sensors and camera(s) would do the trick.

Devices and Sensors, Binary Sensors, Switches and Cameras

The following devices with the sensors attached are created in Home Assistant based on the example default.cfg.yaml from above:

Sensors

Telescope	Camera	Camera File	Switch	Focuser	FilterWheel	Dome	Rotator
Altitude	Camera state	Image Type	Max switch	Position	Position	Altitude	Mechanical position
Azimuth	CCD temperature	Exposure Duration	Switch Value 0		Names	Azimuth	Position
Declination	Cooler Power	Time of observation	Switch Value 1		Current
Declination rate	Image array	X axis binning	Switch Value ...
Guiderate declination	Last exposure duration	Y axis binning
Right ascension	Last exposure start time	Gain
Right ascension rate	Percent completed	Offset
Guiderate right ascension	Readout mode	Pixel X axis size
Side of pier	Readout modes	Pixel Y axis size
Site elevation	Sensor type	Imaging instrument
Site Latitude		CCD temperature
Site Longitude		Filter
		Sensor readout mode
		Sensor Bayer pattern
		Telescope
		Focal length
		RA of telescope
		Declination of telescope
		Altitude of telescope
		Azimuth of telescope
		Object of interest
		RA of imaged object
		Declination of imaged object
		Rotation of imaged object
		Software

Binary Sensors

Telescope	Camera	Focuser	Dome	SafetyMonitor
At home	Cooler On	Is moving	At home	Is safe
At park	Image Ready		At park
Slewing			Shutter status

Switches

Telescope	Camera	Camera File	Switch	Focuser	FilterWheel	Dome	Rotator	SafetyMonitor
			Switch 0
			Switch 1
			Switch ...

My personal Lovelace configuration using mushroom-entity-card, button-card, grid and picture-entity:

Sending Commands

Sending commands to the observatory is implemented by the use of input texts and the mqtt publisher service of Home Assistant. To not accidentaly park/slew the scope or power of the camera during an imaging session I'm intentionally using dedicated buttons to send a command.

Input Texts

The initial values of RA and DEC are pointing to Polaris

Show YAML

astrolive_target_ra_h:
  name: Target RA h
  min: 0
  max: 24
  initial: 02

astrolive_target_ra_m:
  name: Target RA m
  min: 0
  max: 60
  initial: 59

astrolive_target_ra_s:
  name: Target RA s
  min: 0
  max: 60
  initial: 58.71

astrolive_target_dec_d:
  name: Target DEC d
  min: -90
  max: 90
  initial: 89

astrolive_target_dec_m:
  name: Target DEC m
  min: 0
  max: 60
  initial: 21

astrolive_target_dec_s:
  name: Target DEC s
  min: 0
  max: 60
  initial: 30.5

astrolive_focuser_position:
  name: Focuser Position
  min: 0
  max: 35000
  initial: 10000

Scripts

Sending a single command like park and unpark.

Show YAML

alias: AstroLive - Send Command
sequence:
  - service: mqtt.publish
    data:
      topic: astrolive/command
      payload_template: >
        {{ '{{ "component": "{}", "command": "{}" }}'.format( component,
        command) }}
mode: single

Slewing the telescope.

Show YAML

alias: AstroLive - Send Command Slew
sequence:
  - service: mqtt.publish
    data:
      topic: astrolive/command
      payload_template: >
        {{ '{{ "component": "{}", "command": "slew", "ra": "{}", "dec": "{}"
        }}'.format( component | trim, ra | trim, dec | trim ) }}
mode: single

Moving the focuser.

Show YAML

alias: AstroLive - Send Command Focuser Move
sequence:
  - service: mqtt.publish
    data:
      topic: astrolive/command
      payload_template: >
        {{ '{{ "component": "{}", "command": "move", "position": "{}"
        }}'.format( component | trim, position | trim ) }}
mode: single

Changing a filter.

Show YAML

alias: AstroLive - Send Command FilterWheel Set Position
sequence:
  - service: mqtt.publish
    data:
      topic: astrolive/command
      payload_template: >
        {{ '{{ "component": "{}", "command": "setposition", "position": "{}"
        }}'.format( component | trim, position | trim ) }}
mode: single

Name		Name	Last commit message	Last commit date
Latest commit History 26 Commits
.github/workflows		.github/workflows
astrolive		astrolive
config		config
images		images
.dockerignore		.dockerignore
.gitignore		.gitignore
CHANGELOG.md		CHANGELOG.md
Dockerfile		Dockerfile
LICENSE		LICENSE
README.md		README.md
build.sh		build.sh
daemon.sh		daemon.sh
requirements.txt		requirements.txt
run.py		run.py
run.sh		run.sh

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

Repository files navigation

AstroLive

Table of Content

How It Works

Breaking Changes when upgrading from Version 0.3

Requirements

My Personal Setup

Usage

Installation and Configuration of ASCOM Remote Server

Get and Configure AstroLive

Run

Integrate with Home Assistant

Devices and Sensors, Binary Sensors, Switches and Cameras

Sensors

Binary Sensors

Switches

Sending Commands

Input Texts

Scripts

About

Releases 6

Packages

Languages

License

mawinkler/astrolive

Folders and files

Latest commit

History

Repository files navigation

AstroLive

Table of Content

How It Works

Breaking Changes when upgrading from Version 0.3

Requirements

My Personal Setup

Usage

Installation and Configuration of ASCOM Remote Server

Get and Configure AstroLive

Run

Integrate with Home Assistant

Devices and Sensors, Binary Sensors, Switches and Cameras

Sensors

Binary Sensors

Switches

Sending Commands

Input Texts

Scripts

About

Topics

Resources

License

Code of conduct

Stars

Watchers

Forks

Releases 6

Packages 0

Languages

Packages