v6 candidate but not finished - not tested #7

kubalewski · 2023-02-11T01:28:43Z

No description provided.

Add a protocol spec for DPLL. Add code generated from the spec. Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Arkadiusz Kubalewski <[email protected]>

DPLL framework is used to represent and configure DPLL devices in systems. Each device that has DPLL and can configure sources and outputs can use this framework. Netlink interface is used to provide configuration data and to receive notification messages about changes in the configuration or status of DPLL device. Inputs and outputs of the DPLL device are represented as special objects which could be dynamically added to and removed from DPLL device. Changes: dpll: redesign after ynl and review comments dpll: replace cookie with clock id dpll: add clock class Provide userspace with clock class value of DPLL with dpll device dump netlink request. Clock class is assigned by driver allocating a dpll device. Clock class values are defined as specified in: ITU-T G.8273.2/Y.1368.2 recommendation. dpll: follow one naming schema in dpll subsys dpll: fix dpll device naming scheme Fix dpll device naming scheme by use of new pattern. "dpll_%s_%d_%d", where: - %s - dev_name(parent) of parent device, - %d (1) - enum value of dpll type, - %d (2) - device index provided by parent device. dpll: remove description length parameter dpll: fix muxed/shared pin registration Let the kernel module to register a shared or muxed pin without finding it or its parent. Instead use a parent/shared pin description to find correct pin internally in dpll_core, simplifing a dpll API. dpll: move function comments to dpll_core.c, fix exports dpll: remove single-use helper functions dpll: merge device register with alloc dpll: lock and unlock mutex on dpll device release dpll: move dpll_type to uapi header dpll: rename DPLLA_DUMP_FILTER to DPLLA_FILTER dpll: rename dpll_pin_state to dpll_pin_mode dpll: rename DPLL_MODE_FORCED to DPLL_MODE_MANUAL dpll: remove DPLL_CHANGE_PIN_TYPE enum value Co-developed-by: Milena Olech <[email protected]> Signed-off-by: Milena Olech <[email protected]> Co-developed-by: Michal Michalik <[email protected]> Signed-off-by: Michal Michalik <[email protected]> Co-developed-by: Arkadiusz Kubalewski <[email protected]> Signed-off-by: Arkadiusz Kubalewski <[email protected]> Signed-off-by: Vadim Fedorenko <[email protected]>

In the function ieee80211_tx_dequeue() there is a particular locking sequence: begin: spin_lock(&local->queue_stop_reason_lock); q_stopped = local->queue_stop_reasons[q]; spin_unlock(&local->queue_stop_reason_lock); However small the chance (increased by ftracetest), an asynchronous interrupt can occur in between of spin_lock() and spin_unlock(), and the interrupt routine will attempt to lock the same &local->queue_stop_reason_lock again. This will cause a costly reset of the CPU and the wifi device or an altogether hang in the single CPU and single core scenario. The only remaining spin_lock(&local->queue_stop_reason_lock) that did not disable interrupts was patched, which should prevent any deadlocks on the same CPU/core and the same wifi device. This is the probable trace of the deadlock: kernel: ================================ kernel: WARNING: inconsistent lock state kernel: 6.3.0-rc6-mt-20230401-00001-gf86822a1170f #4 Tainted: G W kernel: -------------------------------- kernel: inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage. kernel: kworker/5:0/25656 [HC0[0]:SC0[0]:HE1:SE1] takes: kernel: ffff9d6190779478 (&local->queue_stop_reason_lock){+.?.}-{2:2}, at: return_to_handler+0x0/0x40 kernel: {IN-SOFTIRQ-W} state was registered at: kernel: lock_acquire+0xc7/0x2d0 kernel: _raw_spin_lock+0x36/0x50 kernel: ieee80211_tx_dequeue+0xb4/0x1330 [mac80211] kernel: iwl_mvm_mac_itxq_xmit+0xae/0x210 [iwlmvm] kernel: iwl_mvm_mac_wake_tx_queue+0x2d/0xd0 [iwlmvm] kernel: ieee80211_queue_skb+0x450/0x730 [mac80211] kernel: __ieee80211_xmit_fast.constprop.66+0x834/0xa50 [mac80211] kernel: __ieee80211_subif_start_xmit+0x217/0x530 [mac80211] kernel: ieee80211_subif_start_xmit+0x60/0x580 [mac80211] kernel: dev_hard_start_xmit+0xb5/0x260 kernel: __dev_queue_xmit+0xdbe/0x1200 kernel: neigh_resolve_output+0x166/0x260 kernel: ip_finish_output2+0x216/0xb80 kernel: __ip_finish_output+0x2a4/0x4d0 kernel: ip_finish_output+0x2d/0xd0 kernel: ip_output+0x82/0x2b0 kernel: ip_local_out+0xec/0x110 kernel: igmpv3_sendpack+0x5c/0x90 kernel: igmp_ifc_timer_expire+0x26e/0x4e0 kernel: call_timer_fn+0xa5/0x230 kernel: run_timer_softirq+0x27f/0x550 kernel: __do_softirq+0xb4/0x3a4 kernel: irq_exit_rcu+0x9b/0xc0 kernel: sysvec_apic_timer_interrupt+0x80/0xa0 kernel: asm_sysvec_apic_timer_interrupt+0x1f/0x30 kernel: _raw_spin_unlock_irqrestore+0x3f/0x70 kernel: free_to_partial_list+0x3d6/0x590 kernel: __slab_free+0x1b7/0x310 kernel: kmem_cache_free+0x52d/0x550 kernel: putname+0x5d/0x70 kernel: do_sys_openat2+0x1d7/0x310 kernel: do_sys_open+0x51/0x80 kernel: __x64_sys_openat+0x24/0x30 kernel: do_syscall_64+0x5c/0x90 kernel: entry_SYSCALL_64_after_hwframe+0x72/0xdc kernel: irq event stamp: 5120729 kernel: hardirqs last enabled at (5120729): [<ffffffff9d149936>] trace_graph_return+0xd6/0x120 kernel: hardirqs last disabled at (5120728): [<ffffffff9d149950>] trace_graph_return+0xf0/0x120 kernel: softirqs last enabled at (5069900): [<ffffffff9cf65b60>] return_to_handler+0x0/0x40 kernel: softirqs last disabled at (5067555): [<ffffffff9cf65b60>] return_to_handler+0x0/0x40 kernel: other info that might help us debug this: kernel: Possible unsafe locking scenario: kernel: CPU0 kernel: ---- kernel: lock(&local->queue_stop_reason_lock); kernel: <Interrupt> kernel: lock(&local->queue_stop_reason_lock); kernel: *** DEADLOCK *** kernel: 8 locks held by kworker/5:0/25656: kernel: #0: ffff9d618009d138 ((wq_completion)events_freezable){+.+.}-{0:0}, at: process_one_work+0x1ca/0x530 kernel: #1: ffffb1ef4637fe68 ((work_completion)(&local->restart_work)){+.+.}-{0:0}, at: process_one_work+0x1ce/0x530 kernel: #2: ffffffff9f166548 (rtnl_mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40 kernel: #3: ffff9d6190778728 (&rdev->wiphy.mtx){+.+.}-{3:3}, at: return_to_handler+0x0/0x40 kernel: #4: ffff9d619077b480 (&mvm->mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40 kernel: #5: ffff9d61907bacd8 (&trans_pcie->mutex){+.+.}-{3:3}, at: return_to_handler+0x0/0x40 kernel: #6: ffffffff9ef9cda0 (rcu_read_lock){....}-{1:2}, at: iwl_mvm_queue_state_change+0x59/0x3a0 [iwlmvm] kernel: #7: ffffffff9ef9cda0 (rcu_read_lock){....}-{1:2}, at: iwl_mvm_mac_itxq_xmit+0x42/0x210 [iwlmvm] kernel: stack backtrace: kernel: CPU: 5 PID: 25656 Comm: kworker/5:0 Tainted: G W 6.3.0-rc6-mt-20230401-00001-gf86822a1170f #4 kernel: Hardware name: LENOVO 82H8/LNVNB161216, BIOS GGCN51WW 11/16/2022 kernel: Workqueue: events_freezable ieee80211_restart_work [mac80211] kernel: Call Trace: kernel: <TASK> kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: dump_stack_lvl+0x5f/0xa0 kernel: dump_stack+0x14/0x20 kernel: print_usage_bug.part.46+0x208/0x2a0 kernel: mark_lock.part.47+0x605/0x630 kernel: ? sched_clock+0xd/0x20 kernel: ? trace_clock_local+0x14/0x30 kernel: ? __rb_reserve_next+0x5f/0x490 kernel: ? _raw_spin_lock+0x1b/0x50 kernel: __lock_acquire+0x464/0x1990 kernel: ? mark_held_locks+0x4e/0x80 kernel: lock_acquire+0xc7/0x2d0 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ? ftrace_return_to_handler+0x8b/0x100 kernel: ? preempt_count_add+0x4/0x70 kernel: _raw_spin_lock+0x36/0x50 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ieee80211_tx_dequeue+0xb4/0x1330 [mac80211] kernel: ? prepare_ftrace_return+0xc5/0x190 kernel: ? ftrace_graph_func+0x16/0x20 kernel: ? 0xffffffffc02ab0b1 kernel: ? lock_acquire+0xc7/0x2d0 kernel: ? iwl_mvm_mac_itxq_xmit+0x42/0x210 [iwlmvm] kernel: ? ieee80211_tx_dequeue+0x9/0x1330 [mac80211] kernel: ? __rcu_read_lock+0x4/0x40 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_mac_itxq_xmit+0xae/0x210 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_queue_state_change+0x311/0x3a0 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_wake_sw_queue+0x17/0x20 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_txq_gen2_unmap+0x1c9/0x1f0 [iwlwifi] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_txq_gen2_free+0x55/0x130 [iwlwifi] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_txq_gen2_tx_free+0x63/0x80 [iwlwifi] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: _iwl_trans_pcie_gen2_stop_device+0x3f3/0x5b0 [iwlwifi] kernel: ? _iwl_trans_pcie_gen2_stop_device+0x9/0x5b0 [iwlwifi] kernel: ? mutex_lock_nested+0x4/0x30 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_trans_pcie_gen2_stop_device+0x5f/0x90 [iwlwifi] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_stop_device+0x78/0xd0 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: __iwl_mvm_mac_start+0x114/0x210 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: iwl_mvm_mac_start+0x76/0x150 [iwlmvm] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: drv_start+0x79/0x180 [mac80211] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ieee80211_reconfig+0x1523/0x1ce0 [mac80211] kernel: ? synchronize_net+0x4/0x50 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: ieee80211_restart_work+0x108/0x170 [mac80211] kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: process_one_work+0x250/0x530 kernel: ? ftrace_regs_caller_end+0x66/0x66 kernel: worker_thread+0x48/0x3a0 kernel: ? __pfx_worker_thread+0x10/0x10 kernel: kthread+0x10f/0x140 kernel: ? __pfx_kthread+0x10/0x10 kernel: ret_from_fork+0x29/0x50 kernel: </TASK> Fixes: 4444bc2 ("wifi: mac80211: Proper mark iTXQs for resumption") Link: https://lore.kernel.org/all/[email protected]/ Reported-by: Mirsad Goran Todorovac <[email protected]> Cc: Gregory Greenman <[email protected]> Cc: Johannes Berg <[email protected]> Link: https://lore.kernel.org/all/[email protected]/ Cc: David S. Miller <[email protected]> Cc: Eric Dumazet <[email protected]> Cc: Jakub Kicinski <[email protected]> Cc: Paolo Abeni <[email protected]> Cc: Leon Romanovsky <[email protected]> Cc: Alexander Wetzel <[email protected]> Signed-off-by: Mirsad Goran Todorovac <[email protected]> Reviewed-by: Leon Romanovsky <[email protected]> Reviewed-by: tag, or it goes automatically? Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Johannes Berg <[email protected]>

Magnus Karlsson says: ==================== Prepare the AF_XDP selftests test framework code for the upcoming multi-buffer support in AF_XDP. This so that the multi-buffer patch set does not become way too large. In that upcoming patch set, we are only including the multi-buffer tests together with any framework code that depends on the new options bit introduced in the AF_XDP multi-buffer implementation itself. Currently, the test framework is based on the premise that a packet consists of a single fragment and thus occupies a single buffer and a single descriptor. Multi-buffer breaks this assumption, as that is the whole purpose of it. Now, a packet can consist of multiple buffers and therefore consume multiple descriptors. The patch set starts with some clean-ups and simplifications followed by patches that make sure that the current code works even when a packet occupies multiple buffers. The actual code for sending and receiving multi-buffer packets will be included in the AF_XDP multi-buffer patch set as it depends on a new bit being used in the options field of the descriptor. Patch set anatomy: 1: The XDP program was unnecessarily changed many times. Fixes this. 2: There is no reason to generate a full UDP/IPv4 packet as it is never used. Simplify the code by just generating a valid Ethernet frame. 3: Introduce a more complicated payload pattern that can detect fragments out of bounds in a multi-buffer packet and other errors found in single-fragment packets. 4: As a convenience, dump the content of the faulty packet at error. 5: To simplify the code, make the usage of the packet stream for Tx and Rx more similar. 6: Store the offset of the packet in the buffer in the struct pkt definition instead of the address in the umem itself and introduce a simple buffer allocator. The address only made sense when all packets consumed a single buffer. Now, we do not know beforehand how many buffers a packet will consume, so we instead just allocate a buffer from the allocator and specify the offset within that buffer. 7: Test for huge pages only once instead of before each test that needs it. 8: Populate the fill ring based on how many frags are needed for each packet. 9: Change the data generation code so it can generate data for multi-buffer packets too. 10: Adjust the packet pacing algorithm so that it can cope with multi-buffer packets. The pacing algorithm is present so that Tx does not send too many packets/frames to Rx that it starts to drop packets. That would ruin the tests. v1 -> v2: * Fixed spelling error in patch #6 [Simon] * Fixed compilation error with llvm in patch #7 [Daniel] Thanks: Magnus ==================== Signed-off-by: Alexei Starovoitov <[email protected]>

The cited commit adds a compeletion to remove dependency on rtnl lock. But it causes a deadlock for multiple encapsulations: crash> bt ffff8aece8a64000 PID: 1514557 TASK: ffff8aece8a64000 CPU: 3 COMMAND: "tc" #0 [ffffa6d14183f368] __schedule at ffffffffb8ba7f45 #1 [ffffa6d14183f3f8] schedule at ffffffffb8ba8418 #2 [ffffa6d14183f418] schedule_preempt_disabled at ffffffffb8ba8898 #3 [ffffa6d14183f428] __mutex_lock at ffffffffb8baa7f8 #4 [ffffa6d14183f4d0] mutex_lock_nested at ffffffffb8baabeb #5 [ffffa6d14183f4e0] mlx5e_attach_encap at ffffffffc0f48c17 [mlx5_core] #6 [ffffa6d14183f628] mlx5e_tc_add_fdb_flow at ffffffffc0f39680 [mlx5_core] #7 [ffffa6d14183f688] __mlx5e_add_fdb_flow at ffffffffc0f3b636 [mlx5_core] #8 [ffffa6d14183f6f0] mlx5e_tc_add_flow at ffffffffc0f3bcdf [mlx5_core] #9 [ffffa6d14183f728] mlx5e_configure_flower at ffffffffc0f3c1d1 [mlx5_core] #10 [ffffa6d14183f790] mlx5e_rep_setup_tc_cls_flower at ffffffffc0f3d529 [mlx5_core] #11 [ffffa6d14183f7a0] mlx5e_rep_setup_tc_cb at ffffffffc0f3d714 [mlx5_core] #12 [ffffa6d14183f7b0] tc_setup_cb_add at ffffffffb8931bb8 #13 [ffffa6d14183f810] fl_hw_replace_filter at ffffffffc0dae901 [cls_flower] #14 [ffffa6d14183f8d8] fl_change at ffffffffc0db5c57 [cls_flower] #15 [ffffa6d14183f970] tc_new_tfilter at ffffffffb8936047 #16 [ffffa6d14183fac8] rtnetlink_rcv_msg at ffffffffb88c7c31 #17 [ffffa6d14183fb50] netlink_rcv_skb at ffffffffb8942853 #18 [ffffa6d14183fbc0] rtnetlink_rcv at ffffffffb88c1835 #19 [ffffa6d14183fbd0] netlink_unicast at ffffffffb8941f27 #20 [ffffa6d14183fc18] netlink_sendmsg at ffffffffb8942245 #21 [ffffa6d14183fc98] sock_sendmsg at ffffffffb887d482 #22 [ffffa6d14183fcb8] ____sys_sendmsg at ffffffffb887d81a #23 [ffffa6d14183fd38] ___sys_sendmsg at ffffffffb88806e2 vvfedorenko#24 [ffffa6d14183fe90] __sys_sendmsg at ffffffffb88807a2 vvfedorenko#25 [ffffa6d14183ff28] __x64_sys_sendmsg at ffffffffb888080f vvfedorenko#26 [ffffa6d14183ff38] do_syscall_64 at ffffffffb8b9b6a8 vvfedorenko#27 [ffffa6d14183ff50] entry_SYSCALL_64_after_hwframe at ffffffffb8c0007c crash> bt 0xffff8aeb07544000 PID: 1110766 TASK: ffff8aeb07544000 CPU: 0 COMMAND: "kworker/u20:9" #0 [ffffa6d14e6b7bd8] __schedule at ffffffffb8ba7f45 #1 [ffffa6d14e6b7c68] schedule at ffffffffb8ba8418 #2 [ffffa6d14e6b7c88] schedule_timeout at ffffffffb8baef88 #3 [ffffa6d14e6b7d10] wait_for_completion at ffffffffb8ba968b #4 [ffffa6d14e6b7d60] mlx5e_take_all_encap_flows at ffffffffc0f47ec4 [mlx5_core] #5 [ffffa6d14e6b7da0] mlx5e_rep_update_flows at ffffffffc0f3e734 [mlx5_core] #6 [ffffa6d14e6b7df8] mlx5e_rep_neigh_update at ffffffffc0f400bb [mlx5_core] #7 [ffffa6d14e6b7e50] process_one_work at ffffffffb80acc9c #8 [ffffa6d14e6b7ed0] worker_thread at ffffffffb80ad012 #9 [ffffa6d14e6b7f10] kthread at ffffffffb80b615d #10 [ffffa6d14e6b7f50] ret_from_fork at ffffffffb8001b2f After the first encap is attached, flow will be added to encap entry's flows list. If neigh update is running at this time, the following encaps of the flow can't hold the encap_tbl_lock and sleep. If neigh update thread is waiting for that flow's init_done, deadlock happens. Fix it by holding lock outside of the for loop. If neigh update is running, prevent encap flows from offloading. Since the lock is held outside of the for loop, concurrent creation of encap entries is not allowed. So remove unnecessary wait_for_completion call for res_ready. Fixes: 95435ad ("net/mlx5e: Only access fully initialized flows in neigh update") Signed-off-by: Chris Mi <[email protected]> Reviewed-by: Roi Dayan <[email protected]> Reviewed-by: Vlad Buslov <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>

Jiri Pirko says: ==================== devlink: move port ops into separate structure In devlink, some of the objects have separate ops registered alongside with the object itself. Port however have ops in devlink_ops structure. For drivers what register multiple kinds of ports with different ops this is not convenient. This patchset changes does following changes: 1) Introduces devlink_port_ops with functions that allow devlink port to be registered passing a pointer to driver port ops. (patch #1) 2) Converts drivers to define port_ops and register ports passing the ops pointer. (patches #2, #3, #4, #6, #8, and #9) 3) Moves ops from devlink_ops struct to devlink_port_ops. (patches #5, #7, #10-15) No functional changes. ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>

Ido Schimmel says: ==================== Add layer 2 miss indication and filtering tl;dr ===== This patchset adds a single bit to the tc skb extension to indicate that a packet encountered a layer 2 miss in the bridge and extends flower to match on this metadata. This is required for non-DF (Designated Forwarder) filtering in EVPN multi-homing which prevents decapsulated BUM packets from being forwarded multiple times to the same multi-homed host. Background ========== In a typical EVPN multi-homing setup each host is multi-homed using a set of links called ES (Ethernet Segment, i.e., LAG) to multiple leaf switches in a rack. These switches act as VTEPs and are not directly connected (as opposed to MLAG), but can communicate with each other (as well as with VTEPs in remote racks) via spine switches over L3. When a host sends a BUM packet over ES1 to VTEP1, the VTEP will flood it to other VTEPs in the network, including those connected to the host over ES1. The receiving VTEPs must drop the packet and not forward it back to the host. This is called "split-horizon filtering" (SPH) [1]. FRR configures SPH filtering using two tc filters. The first, an ingress filter that matches on packets received from VTEP1 and marks them using a fwmark (firewall mark). The second, an egress filter configured on the LAG interface connected to the host that matches on the fwmark and drops the packets. Example: # tc filter add dev vxlan0 ingress pref 1 proto all flower enc_src_ip $VTEP1_IP action skbedit mark 101 # tc filter add dev bond0 egress pref 1 handle 101 fw action drop Motivation ========== For each ES, only one VTEP is elected by the control plane as the DF. The DF is responsible for forwarding decapsulated BUM traffic to the host over the ES. The non-DF VTEPs must drop such traffic as otherwise the host will receive multiple copies of BUM traffic. This is called "non-DF filtering" [2]. Filtering of multicast and broadcast traffic can be achieved using the following flower filter: # tc filter add dev bond0 egress pref 1 proto all flower indev vxlan0 dst_mac 01:00:00:00:00:00/01:00:00:00:00:00 action drop Unlike broadcast and multicast traffic, it is not currently possible to filter unknown unicast traffic. The classification into unknown unicast is performed by the bridge driver, but is not visible to other layers. Implementation ============== The proposed solution is to add a single bit to the tc skb extension that is set by the bridge for packets that encountered an FDB or MDB miss. The flower classifier is extended to be able to match on this new metadata bit in a similar fashion to existing metadata options such as 'indev'. A bit that is set for every flooded packet would also work, but it does not allow us to differentiate between registered and unregistered multicast traffic which might be useful in the future. A relatively generic name is chosen for this bit - 'l2_miss' - to allow its use to be extended to other layer 2 devices such as VXLAN, should a use case arise. With the above, the control plane can implement a non-DF filter using the following tc filters: # tc filter add dev bond0 egress pref 1 proto all flower indev vxlan0 dst_mac 01:00:00:00:00:00/01:00:00:00:00:00 action drop # tc filter add dev bond0 egress pref 2 proto all flower indev vxlan0 l2_miss true action drop The first drops broadcast and multicast traffic and the second drops unknown unicast traffic. Testing ======= A test exercising the different permutations of the 'l2_miss' bit is added in patch #8. Patchset overview ================= Patch #1 adds the new bit to the tc skb extension and sets it in the bridge driver for packets that encountered a miss. The marking of the packets and the use of this extension is protected by the 'tc_skb_ext_tc' static key in order to keep performance impact to a minimum when the feature is not in use. Patch #2 extends the flow dissector to dissect this information from the tc skb extension into the 'FLOW_DISSECTOR_KEY_META' key. Patch #3 extends the flower classifier to be able to match on the new layer 2 miss metadata. The classifier enables the 'tc_skb_ext_tc' static key upon the installation of the first filter that matches on 'l2_miss' and disables the key upon the removal of the last filter that matches on it. Patch #4 rejects matching on the new metadata in drivers that already support the 'FLOW_DISSECTOR_KEY_META' key. Patches #5-#6 are small preparations in mlxsw. Patch #7 extends mlxsw to be able to match on layer 2 miss. Patch #8 adds a selftest. iproute2 patches can be found here [3]. [1] https://datatracker.ietf.org/doc/html/rfc7432#section-8.3 [2] https://datatracker.ietf.org/doc/html/rfc7432#section-8.5 [3] https://github.com/idosch/iproute2/tree/submit/non_df_filter_v1 [4] https://lore.kernel.org/netdev/[email protected]/ [5] https://lore.kernel.org/netdev/[email protected]/ ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>

Petr Machata says: ==================== mlxsw, selftests: Cleanups This patchset consolidates a number of disparate items that can all be considered cleanups. They are all related to mlxsw in that they are directly in mlxsw code, or in selftests that mlxsw heavily uses. - patch #1 fixes a comment, patch #2 propagates an extack - patches #3 and #4 tweak several loops to query a resource once and cache in a local variable instead of querying on each iteration - patches #5 and #6 fix selftest diagrams, and #7 adds a missing diagram into an existing test - patch #8 disables a PVID on a bridge in a selftest that should not need said PVID ==================== Signed-off-by: David S. Miller <[email protected]>

A remote DoS vulnerability of RPL Source Routing is assigned CVE-2023-2156. The Source Routing Header (SRH) has the following format: 0 1 2 3 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Next Header | Hdr Ext Len | Routing Type | Segments Left | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | CmprI | CmprE | Pad | Reserved | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | | . . . Addresses[1..n] . . . | | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ The originator of an SRH places the first hop's IPv6 address in the IPv6 header's IPv6 Destination Address and the second hop's IPv6 address as the first address in Addresses[1..n]. The CmprI and CmprE fields indicate the number of prefix octets that are shared with the IPv6 Destination Address. When CmprI or CmprE is not 0, Addresses[1..n] are compressed as follows: 1..n-1 : (16 - CmprI) bytes n : (16 - CmprE) bytes Segments Left indicates the number of route segments remaining. When the value is not zero, the SRH is forwarded to the next hop. Its address is extracted from Addresses[n - Segment Left + 1] and swapped with IPv6 Destination Address. When Segment Left is greater than or equal to 2, the size of SRH is not changed because Addresses[1..n-1] are decompressed and recompressed with CmprI. OTOH, when Segment Left changes from 1 to 0, the new SRH could have a different size because Addresses[1..n-1] are decompressed with CmprI and recompressed with CmprE. Let's say CmprI is 15 and CmprE is 0. When we receive SRH with Segment Left >= 2, Addresses[1..n-1] have 1 byte for each, and Addresses[n] has 16 bytes. When Segment Left is 1, Addresses[1..n-1] is decompressed to 16 bytes and not recompressed. Finally, the new SRH will need more room in the header, and the size is (16 - 1) * (n - 1) bytes. Here the max value of n is 255 as Segment Left is u8, so in the worst case, we have to allocate 3825 bytes in the skb headroom. However, now we only allocate a small fixed buffer that is IPV6_RPL_SRH_WORST_SWAP_SIZE (16 + 7 bytes). If the decompressed size overflows the room, skb_push() hits BUG() below [0]. Instead of allocating the fixed buffer for every packet, let's allocate enough headroom only when we receive SRH with Segment Left 1. [0]: skbuff: skb_under_panic: text:ffffffff81c9f6e2 len:576 put:576 head:ffff8880070b5180 data:ffff8880070b4fb0 tail:0x70 end:0x140 dev:lo kernel BUG at net/core/skbuff.c:200! invalid opcode: 0000 [#1] PREEMPT SMP PTI CPU: 0 PID: 154 Comm: python3 Not tainted 6.4.0-rc4-00190-gc308e9ec0047 #7 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.16.0-0-gd239552ce722-prebuilt.qemu.org 04/01/2014 RIP: 0010:skb_panic (net/core/skbuff.c:200) Code: 4f 70 50 8b 87 bc 00 00 00 50 8b 87 b8 00 00 00 50 ff b7 c8 00 00 00 4c 8b 8f c0 00 00 00 48 c7 c7 80 6e 77 82 e8 ad 8b 60 ff <0f> 0b 66 66 2e 0f 1f 84 00 00 00 00 00 90 90 90 90 90 90 90 90 90 RSP: 0018:ffffc90000003da0 EFLAGS: 00000246 RAX: 0000000000000085 RBX: ffff8880058a6600 RCX: 0000000000000000 RDX: 0000000000000000 RSI: ffff88807dc1c540 RDI: ffff88807dc1c540 RBP: ffffc90000003e48 R08: ffffffff82b392c8 R09: 00000000ffffdfff R10: ffffffff82a592e0 R11: ffffffff82b092e0 R12: ffff888005b1c800 R13: ffff8880070b51b8 R14: ffff888005b1ca18 R15: ffff8880070b5190 FS: 00007f4539f0b740(0000) GS:ffff88807dc00000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 000055670baf3000 CR3: 0000000005b0e000 CR4: 00000000007506f0 PKRU: 55555554 Call Trace: <IRQ> skb_push (net/core/skbuff.c:210) ipv6_rthdr_rcv (./include/linux/skbuff.h:2880 net/ipv6/exthdrs.c:634 net/ipv6/exthdrs.c:718) ip6_protocol_deliver_rcu (net/ipv6/ip6_input.c:437 (discriminator 5)) ip6_input_finish (./include/linux/rcupdate.h:805 net/ipv6/ip6_input.c:483) __netif_receive_skb_one_core (net/core/dev.c:5494) process_backlog (./include/linux/rcupdate.h:805 net/core/dev.c:5934) __napi_poll (net/core/dev.c:6496) net_rx_action (net/core/dev.c:6565 net/core/dev.c:6696) __do_softirq (./arch/x86/include/asm/jump_label.h:27 ./include/linux/jump_label.h:207 ./include/trace/events/irq.h:142 kernel/softirq.c:572) do_softirq (kernel/softirq.c:472 kernel/softirq.c:459) </IRQ> <TASK> __local_bh_enable_ip (kernel/softirq.c:396) __dev_queue_xmit (net/core/dev.c:4272) ip6_finish_output2 (./include/net/neighbour.h:544 net/ipv6/ip6_output.c:134) rawv6_sendmsg (./include/net/dst.h:458 ./include/linux/netfilter.h:303 net/ipv6/raw.c:656 net/ipv6/raw.c:914) sock_sendmsg (net/socket.c:724 net/socket.c:747) __sys_sendto (net/socket.c:2144) __x64_sys_sendto (net/socket.c:2156 net/socket.c:2152 net/socket.c:2152) do_syscall_64 (arch/x86/entry/common.c:50 arch/x86/entry/common.c:80) entry_SYSCALL_64_after_hwframe (arch/x86/entry/entry_64.S:120) RIP: 0033:0x7f453a138aea Code: d8 64 89 02 48 c7 c0 ff ff ff ff eb b8 0f 1f 00 f3 0f 1e fa 41 89 ca 64 8b 04 25 18 00 00 00 85 c0 75 15 b8 2c 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 7e c3 0f 1f 44 00 00 41 54 48 83 ec 30 44 89 RSP: 002b:00007ffcc212a1c8 EFLAGS: 00000246 ORIG_RAX: 000000000000002c RAX: ffffffffffffffda RBX: 00007ffcc212a288 RCX: 00007f453a138aea RDX: 0000000000000060 RSI: 00007f4539084c20 RDI: 0000000000000003 RBP: 00007f4538308e80 R08: 00007ffcc212a300 R09: 000000000000001c R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 R13: ffffffffc4653600 R14: 0000000000000001 R15: 00007f4539712d1b </TASK> Modules linked in: Fixes: 8610c7c ("net: ipv6: add support for rpl sr exthdr") Reported-by: Max VA Closes: https://www.interruptlabs.co.uk/articles/linux-ipv6-route-of-death Signed-off-by: Kuniyuki Iwashima <[email protected]> Reviewed-by: Eric Dumazet <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>

Currently, the per cpu upcall counters are allocated after the vport is created and inserted into the system. This could lead to the datapath accessing the counters before they are allocated resulting in a kernel Oops. Here is an example: PID: 59693 TASK: ffff0005f4f51500 CPU: 0 COMMAND: "ovs-vswitchd" #0 [ffff80000a39b5b0] __switch_to at ffffb70f0629f2f4 #1 [ffff80000a39b5d0] __schedule at ffffb70f0629f5cc #2 [ffff80000a39b650] preempt_schedule_common at ffffb70f0629fa60 #3 [ffff80000a39b670] dynamic_might_resched at ffffb70f0629fb58 #4 [ffff80000a39b680] mutex_lock_killable at ffffb70f062a1388 #5 [ffff80000a39b6a0] pcpu_alloc at ffffb70f0594460c #6 [ffff80000a39b750] __alloc_percpu_gfp at ffffb70f05944e68 #7 [ffff80000a39b760] ovs_vport_cmd_new at ffffb70ee6961b90 [openvswitch] ... PID: 58682 TASK: ffff0005b2f0bf00 CPU: 0 COMMAND: "kworker/0:3" #0 [ffff80000a5d2f40] machine_kexec at ffffb70f056a0758 #1 [ffff80000a5d2f70] __crash_kexec at ffffb70f057e2994 #2 [ffff80000a5d3100] crash_kexec at ffffb70f057e2ad8 #3 [ffff80000a5d3120] die at ffffb70f0628234c #4 [ffff80000a5d31e0] die_kernel_fault at ffffb70f062828a8 #5 [ffff80000a5d3210] __do_kernel_fault at ffffb70f056a31f4 #6 [ffff80000a5d3240] do_bad_area at ffffb70f056a32a4 #7 [ffff80000a5d3260] do_translation_fault at ffffb70f062a9710 #8 [ffff80000a5d3270] do_mem_abort at ffffb70f056a2f74 #9 [ffff80000a5d32a0] el1_abort at ffffb70f06297dac #10 [ffff80000a5d32d0] el1h_64_sync_handler at ffffb70f06299b24 #11 [ffff80000a5d3410] el1h_64_sync at ffffb70f056812dc #12 [ffff80000a5d3430] ovs_dp_upcall at ffffb70ee6963c84 [openvswitch] #13 [ffff80000a5d3470] ovs_dp_process_packet at ffffb70ee6963fdc [openvswitch] #14 [ffff80000a5d34f0] ovs_vport_receive at ffffb70ee6972c78 [openvswitch] #15 [ffff80000a5d36f0] netdev_port_receive at ffffb70ee6973948 [openvswitch] #16 [ffff80000a5d3720] netdev_frame_hook at ffffb70ee6973a28 [openvswitch] #17 [ffff80000a5d3730] __netif_receive_skb_core.constprop.0 at ffffb70f06079f90 We moved the per cpu upcall counter allocation to the existing vport alloc and free functions to solve this. Fixes: 95637d9 ("net: openvswitch: release vport resources on failure") Fixes: 1933ea3 ("net: openvswitch: Add support to count upcall packets") Signed-off-by: Eelco Chaudron <[email protected]> Reviewed-by: Simon Horman <[email protected]> Acked-by: Aaron Conole <[email protected]> Signed-off-by: David S. Miller <[email protected]>

Petr Machata says: ==================== mlxsw: Cleanups in router code This patchset moves some router-related code from spectrum.c to spectrum_router.c where it should be. It also simplifies handlers of netevent notifications. - Patch #1 caches router pointer in a dedicated variable. This obviates the need to access the same as mlxsw_sp->router, making lines shorter, and permitting a future patch to add code that fits within 80 character limit. - Patch #2 moves IP / IPv6 validation notifier blocks from spectrum.c to spectrum_router, where the handlers are anyway. - In patch #3, pass router pointer to scheduler of deferred work directly, instead of having it deduce it on its own. - This makes the router pointer available in the handler function mlxsw_sp_router_netevent_event(), so in patch #4, use it directly, instead of finding it through mlxsw_sp_port. - In patch #5, extend mlxsw_sp_router_schedule_work() so that the NETEVENT_NEIGH_UPDATE handler can use it directly instead of inlining equivalent code. - In patches #6 and #7, add helpers for two common operations involving a backing netdev of a RIF. This makes it unnecessary for the function mlxsw_sp_rif_dev() to be visible outside of the router module, so in patch #8, hide it. ==================== Signed-off-by: David S. Miller <[email protected]>

Petr Machata says: ==================== mlxsw: Preparations for out-of-order-operations patches The mlxsw driver currently makes the assumption that the user applies configuration in a bottom-up manner. Thus netdevices need to be added to the bridge before IP addresses are configured on that bridge or SVI added on top of it. Enslaving a netdevice to another netdevice that already has uppers is in fact forbidden by mlxsw for this reason. Despite this safety, it is rather easy to get into situations where the offloaded configuration is just plain wrong. As an example, take a front panel port, configure an IP address: it gets a RIF. Now enslave the port to a bridge, and the RIF is gone. Remove the port from the bridge again, but the RIF never comes back. There is a number of similar situations, where changing the configuration there and back utterly breaks the offload. Over the course of the following several patchsets, mlxsw code is going to be adjusted to diminish the space of wrongly offloaded configurations. Ideally the offload state will reflect the actual state, regardless of the sequence of operation used to construct that state. No functional changes are intended in this patchset yet. Rather the patches prepare the codebase for easier introduction of functional changes in later patchsets. - In patch #1, extract a helper to join a RIF of a given port, if there is one. In patch #2, use it in a newly-added helper to join a LAG interface. - In patches #3, #4 and #5, add helpers that abstract away the rif->dev access. This will make it simpler in the future to change the way the deduction is done. In patch #6, do this for deduction from nexthop group info to RIF. - In patch #7, add a helper to destroy a RIF. So far RIF was destroyed simply by kfree'ing it. - In patch #8, add a helper to check if any IP addresses are configured on a netdevice. This helper will be useful later. - In patch #9, add a helper to migrate a RIF. This will be a convenient place to put extensions later on. - Patch #10 move IPIP initialization up to make ipip_ops_arr available earlier. ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Paolo Abeni <[email protected]>

…hes-in-mlxsw' Petr Machata says: ==================== selftests: Preparations for out-of-order-operations patches in mlxsw The mlxsw driver currently makes the assumption that the user applies configuration in a bottom-up manner. Thus netdevices need to be added to the bridge before IP addresses are configured on that bridge or SVI added on top of it. Enslaving a netdevice to another netdevice that already has uppers is in fact forbidden by mlxsw for this reason. Despite this safety, it is rather easy to get into situations where the offloaded configuration is just plain wrong. Over the course of the following several patchsets, mlxsw code is going to be adjusted to diminish the space of wrongly offloaded configurations. Ideally the offload state will reflect the actual state, regardless of the sequence of operation used to construct that state. Several selftests build configurations that will not be offloadable in the future on some systems. The reason is that what will get offloaded is the actual configuration, not the configuration steps. For example, when a port is added to a bridge that has an IP address, that bridge will get a RIF, which it would not have with the current code. But on Nvidia Spectrum-1 machines, MAC addresses of all RIFs need to have the same prefix, which the bridge will violate. The RIF thus couldn't be created, and the enslavement is therefore canceled, because it would lead to an unoffloadable configuration. This breaks some selftests. In this patchset, adjust selftests to avoid the configurations that mlxsw would be incapable of offloading, while maintaining relevance with regards to the feature that is being tested. There are generally two cases of fixes: - Disabling IPv6 autogen on bridges that do not participate in routing, either because of the abovementioned requirement to keep the same MAC prefix on all in-HW router interfaces, or, on 802.1ad bridges, because in-HW router interfaces are not supported at all. - Setting the bridge MAC address to what it will become after the first member port is attached, so that the in-HW router interface is created with a supported MAC address. The patchset is then split thus: - Patches #1-#7 adjust generic selftests - Patches #8-#16 adjust mlxsw-specific selftests ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>

Petr Machata says: ==================== mlxsw: Maintain candidate RIFs The mlxsw driver currently makes the assumption that the user applies configuration in a bottom-up manner. Thus netdevices need to be added to the bridge before IP addresses are configured on that bridge or SVI added on top of it. Enslaving a netdevice to another netdevice that already has uppers is in fact forbidden by mlxsw for this reason. Despite this safety, it is rather easy to get into situations where the offloaded configuration is just plain wrong. As an example, take a front panel port, configure an IP address: it gets a RIF. Now enslave the port to the bridge, and the RIF is gone. Remove the port from the bridge again, but the RIF never comes back. There is a number of similar situations, where changing the configuration there and back utterly breaks the offload. The situation is going to be made better by implementing a range of replays and post-hoc offloads. This patch set lays the ground for replay of next hops. The particular issue that it deals with is that currently, driver-specific bookkeeping for next hops is hooked off RIF objects, which come and go across the lifetime of a netdevice. We would rather keep these objects at an entity that mirrors the lifetime of the netdevice itself. That way they are at hand and can be offloaded when a RIF is eventually created. To that end, with this patchset, mlxsw keeps a hash table of CRIFs: candidate RIFs, persistent handles for netdevices that mlxsw deems potentially interesting. The lifetime of a CRIF matches that of the underlying netdevice, and thus a RIF can always assume a CRIF exists. A CRIF is where next hops are kept, and when RIF is created, these next hops can be easily offloaded. (Previously only the next hops created after the RIF was created were offloaded.) - Patches #1 and #2 are minor adjustments. - In patches #3 and #4, add CRIF bookkeeping. - In patch #5, link CRIFs to RIFs such that given a netdevice-backed RIF, the corresponding CRIF is easy to look up. - Patch #6 is a clean-up allowed by the previous patches - Patches #7 and #8 move next hop tracking to CRIFs No observable effects are intended as of yet. This will be useful once there is support for RIF creation for netdevices that become mlxsw uppers, which will come in following patch sets. ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>

Petr Machata says: ==================== mlxsw: Permit enslavement to netdevices with uppers The mlxsw driver currently makes the assumption that the user applies configuration in a bottom-up manner. Thus netdevices need to be added to the bridge before IP addresses are configured on that bridge or SVI added on top of it. Enslaving a netdevice to another netdevice that already has uppers is in fact forbidden by mlxsw for this reason. Despite this safety, it is rather easy to get into situations where the offloaded configuration is just plain wrong. As an example, take a front panel port, configure an IP address: it gets a RIF. Now enslave the port to the bridge, and the RIF is gone. Remove the port from the bridge again, but the RIF never comes back. There is a number of similar situations, where changing the configuration there and back utterly breaks the offload. Similarly, detaching a front panel port from a configured topology means unoffloading of this whole topology -- VLAN uppers, next hops, etc. Attaching the port back is then not permitted at all. If it were, it would not result in a working configuration, because much of mlxsw is written to react to changes in immediate configuration. There is nothing that would go visit netdevices in the attached-to topology and offload existing routes and VLAN memberships, for example. In this patchset, introduce a number of replays to be invoked so that this sort of post-hoc offload is supported. Then remove the vetoes that disallowed enslavement of front panel ports to other netdevices with uppers. The patchset progresses as follows: - In patch #1, fix an issue in the bridge driver. To my knowledge, the issue could not have resulted in a buggy behavior previously, and thus is packaged with this patchset instead of being sent separately to net. - In patch #2, add a new helper to the switchdev code. - In patch #3, drop mlxsw selftests that will not be relevant after this patchset anymore. - Patches #4, #5, #6, #7 and #8 prepare the codebase for smoother introduction of the rest of the code. - Patches #9, #10, #11, #12, #13 and #14 replay various aspects of upper configuration when a front panel port is introduced into a topology. Individual patches take care of bridge and LAG RIF memberships, switchdev replay, nexthop and neighbors replay, and MACVLAN offload. - Patches #15 and #16 introduce RIFs for newly-relevant netdevices when a front panel port is enslaved (in which case all uppers are newly relevant), or, respectively, deslaved (in which case the newly-relevant netdevice is the one being deslaved). - Up until this point, the introduced scaffolding was not really used, because mlxsw still forbids enslavement of mlxsw netdevices to uppers with uppers. In patch #17, this condition is finally relaxed. A sizable selftest suite is available to test all this new code. That will be sent in a separate patchset. ==================== Signed-off-by: David S. Miller <[email protected]>

The cited commit holds encap tbl lock unconditionally when setting up dests. But it may cause the following deadlock: PID: 1063722 TASK: ffffa062ca5d0000 CPU: 13 COMMAND: "handler8" #0 [ffffb14de05b7368] __schedule at ffffffffa1d5aa91 #1 [ffffb14de05b7410] schedule at ffffffffa1d5afdb #2 [ffffb14de05b7430] schedule_preempt_disabled at ffffffffa1d5b528 #3 [ffffb14de05b7440] __mutex_lock at ffffffffa1d5d6cb #4 [ffffb14de05b74e8] mutex_lock_nested at ffffffffa1d5ddeb #5 [ffffb14de05b74f8] mlx5e_tc_tun_encap_dests_set at ffffffffc12f2096 [mlx5_core] #6 [ffffb14de05b7568] post_process_attr at ffffffffc12d9fc5 [mlx5_core] #7 [ffffb14de05b75a0] mlx5e_tc_add_fdb_flow at ffffffffc12de877 [mlx5_core] #8 [ffffb14de05b75f0] __mlx5e_add_fdb_flow at ffffffffc12e0eef [mlx5_core] #9 [ffffb14de05b7660] mlx5e_tc_add_flow at ffffffffc12e12f7 [mlx5_core] #10 [ffffb14de05b76b8] mlx5e_configure_flower at ffffffffc12e1686 [mlx5_core] #11 [ffffb14de05b7720] mlx5e_rep_indr_offload at ffffffffc12e3817 [mlx5_core] #12 [ffffb14de05b7730] mlx5e_rep_indr_setup_tc_cb at ffffffffc12e388a [mlx5_core] #13 [ffffb14de05b7740] tc_setup_cb_add at ffffffffa1ab2ba8 #14 [ffffb14de05b77a0] fl_hw_replace_filter at ffffffffc0bdec2f [cls_flower] #15 [ffffb14de05b7868] fl_change at ffffffffc0be6caa [cls_flower] #16 [ffffb14de05b7908] tc_new_tfilter at ffffffffa1ab71f0 [1031218.028143] wait_for_completion+0x24/0x30 [1031218.028589] mlx5e_update_route_decap_flows+0x9a/0x1e0 [mlx5_core] [1031218.029256] mlx5e_tc_fib_event_work+0x1ad/0x300 [mlx5_core] [1031218.029885] process_one_work+0x24e/0x510 Actually no need to hold encap tbl lock if there is no encap action. Fix it by checking if encap action exists or not before holding encap tbl lock. Fixes: 37c3b9f ("net/mlx5e: Prevent encap offload when neigh update is running") Signed-off-by: Chris Mi <[email protected]> Reviewed-by: Vlad Buslov <[email protected]> Signed-off-by: Saeed Mahameed <[email protected]>

In internal testing of test_maps, we sometimes observed failures like: test_maps: test_maps.c:173: void test_hashmap_percpu(unsigned int, void *): Assertion `bpf_map_update_elem(fd, &key, value, BPF_ANY) == 0' failed. where the errno is ENOMEM. After some troubleshooting and enabling the warnings, we saw: [ 91.304708] percpu: allocation failed, size=8 align=8 atomic=1, atomic alloc failed, no space left [ 91.304716] CPU: 51 PID: 24145 Comm: test_maps Kdump: loaded Tainted: G N 6.1.38-smp-DEV #7 [ 91.304719] Hardware name: Google Astoria/astoria, BIOS 0.20230627.0-0 06/27/2023 [ 91.304721] Call Trace: [ 91.304724] <TASK> [ 91.304730] [<ffffffffa7ef83b9>] dump_stack_lvl+0x59/0x88 [ 91.304737] [<ffffffffa7ef83f8>] dump_stack+0x10/0x18 [ 91.304738] [<ffffffffa75caa0c>] pcpu_alloc+0x6fc/0x870 [ 91.304741] [<ffffffffa75ca302>] __alloc_percpu_gfp+0x12/0x20 [ 91.304743] [<ffffffffa756785e>] alloc_bulk+0xde/0x1e0 [ 91.304746] [<ffffffffa7566c02>] bpf_mem_alloc_init+0xd2/0x2f0 [ 91.304747] [<ffffffffa7547c69>] htab_map_alloc+0x479/0x650 [ 91.304750] [<ffffffffa751d6e0>] map_create+0x140/0x2e0 [ 91.304752] [<ffffffffa751d413>] __sys_bpf+0x5a3/0x6c0 [ 91.304753] [<ffffffffa751c3ec>] __x64_sys_bpf+0x1c/0x30 [ 91.304754] [<ffffffffa7ef847a>] do_syscall_64+0x5a/0x80 [ 91.304756] [<ffffffffa800009b>] entry_SYSCALL_64_after_hwframe+0x63/0xcd This makes sense, because in atomic context, percpu allocation would not create new chunks; it would only create in non-atomic contexts. And if during prefill all precpu chunks are full, -ENOMEM would happen immediately upon next unit_alloc. Prefill phase does not actually run in atomic context, so we can use this fact to allocate non-atomically with GFP_KERNEL instead of GFP_NOWAIT. This avoids the immediate -ENOMEM. GFP_NOWAIT has to be used in unit_alloc when bpf program runs in atomic context. Even if bpf program runs in non-atomic context, in most cases, rcu read lock is enabled for the program so GFP_NOWAIT is still needed. This is often also the case for BPF_MAP_UPDATE_ELEM syscalls. Signed-off-by: YiFei Zhu <[email protected]> Acked-by: Yonghong Song <[email protected]> Acked-by: Hou Tao <[email protected]> Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Alexei Starovoitov <[email protected]>

…inux/kernel/git/saeed/linux Saeed Mahameed says: ==================== mlx5-updates-2023-08-07 1) Few cleanups 2) Dynamic completion EQs The driver creates completion EQs for all vectors directly on driver load, even if those EQs will not be utilized later on. To allow more flexibility in managing completion EQs and to reduce the memory overhead of driver load, this series will adjust completion EQs creation to be dynamic. Meaning, completion EQs will be created only when needed. Patch #1 introduces a counter for tracking the current number of completion EQs. Patches #2-6 refactor the existing infrastructure of managing completion EQs and completion IRQs to be compatible with per-vector allocation/release requests. Patches #7-8 modify the CPU-to-IRQ affinity calculation to be resilient in case the affinity is requested but completion IRQ is not allocated yet. Patch #9 function rename. Patch #10 handles the corner case of SF performing an IRQ request when no SF IRQ pool is found, and no PF IRQ exists for the same vector. Patch #11 modify driver to use dynamically allocate completion EQs. * tag 'mlx5-updates-2023-08-07' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux: net/mlx5: Bridge, Only handle registered netdev bridge events net/mlx5: E-Switch, Remove redundant arg ignore_flow_lvl net/mlx5: Fix typo reminder -> remainder net/mlx5: remove many unnecessary NULL values net/mlx5: Allocate completion EQs dynamically net/mlx5: Handle SF IRQ request in the absence of SF IRQ pool net/mlx5: Rename mlx5_comp_vectors_count() to mlx5_comp_vectors_max() net/mlx5: Add IRQ vector to CPU lookup function net/mlx5: Introduce mlx5_cpumask_default_spread net/mlx5: Implement single completion EQ create/destroy methods net/mlx5: Use xarray to store and manage completion EQs net/mlx5: Refactor completion IRQ request/release handlers in EQ layer net/mlx5: Use xarray to store and manage completion IRQs net/mlx5: Refactor completion IRQ request/release API net/mlx5: Track the current number of completion EQs ==================== Link: https://lore.kernel.org/r/[email protected] Signed-off-by: Jakub Kicinski <[email protected]>

kubalewski added 2 commits February 11, 2023 02:22

dpll: spec: Add Netlink spec in YAML

0abdb92

Add a protocol spec for DPLL. Add code generated from the spec. Signed-off-by: Jakub Kicinski <[email protected]> Signed-off-by: Arkadiusz Kubalewski <[email protected]>

Provide feedback

Saved searches

Use saved searches to filter your results more quickly

v6 candidate but not finished - not tested #7

v6 candidate but not finished - not tested #7

kubalewski commented Feb 11, 2023

v6 candidate but not finished - not tested #7

Are you sure you want to change the base?

v6 candidate but not finished - not tested #7

Conversation

kubalewski commented Feb 11, 2023