rv8803

Quickstart

Tip

At the end you will see a link to the latest docs which you can view locally.

Build this by running:

./build.sh

Note

You will need to configure your target MCU accordingly.

This example uses the stm32wle5cc metapac configuration for the RAKwireless RAK3172 module.

#[embassy_executor::main]
async fn main(_spawner: Spawner) -> ! {
    let mut config = Config::default();
    {
        use embassy_stm32::rcc::*;
        config.rcc.hsi = true;
        config.rcc.hse = None;
        config.rcc.pll = Some(Pll {
            source: PllSource::HSI,
            prediv: PllPreDiv::DIV1, // PLLM
            mul: PllMul::MUL21,      // PLLN
            divp: Some(PllPDiv::DIV2),
            divq: Some(PllQDiv::DIV2), // PLLQ
            divr: Some(PllRDiv::DIV7), // PLL1_R
        });
        config.rcc.sys = Sysclk::PLL1_R;
        config.rcc.ahb_pre = AHBPrescaler::DIV1;
        config.rcc.apb1_pre = APBPrescaler::DIV1;
        config.rcc.apb2_pre = APBPrescaler::DIV1;
    }
    let p = embassy_stm32::init(config);
    info!("Configure STM32 for Skynet(TM) AI bootup. Muwahahahahhaha!");

    let i2c2_periph = p.I2C2;
    let led2 = p.PA0;
    let led2 = &mut gpio::Output::new(led2, gpio::Level::Low, gpio::Speed::Medium);

    // RAK19007 board J12
    //  - pin 1: VCC 3V3
    //  - pin 2: GND
    //  - pin 3: SCL
    //  - pin 4: SDA
    //
    // RAK3172 Package (STM32wle5cc)
    // https://docs.embassy.dev/embassy-stm32/git/stm32wle5cc/i2c/trait.SclPin.html
    // https://docs.embassy.dev/embassy-stm32/git/stm32wle5cc/i2c/trait.SdaPin.html
    let mut i2c = I2c::new_blocking(
        i2c2_periph,
        p.PA12, // scl
        p.PA11, // sda
        Hertz(400_000),
        Default::default(),
    );

    let mut rv8803: Driver<i2c::I2c<'_, mode::Blocking>, SevenBitAddress> = Driver::new(i2c);

    let mut data = Some(rv8803::ClockData::new());
    // let mut data: Option<ClockData> = None;

    if let Some(mut d) = data {
        let now = DateTimeBuilder::new()
            .year(CurrentYear::new(2024))
            .month(Month::October)
            .date(7)
            .weekday(Weekday::Monday)
            .hours(0)
            .minutes(0)
            .seconds(0)
            .build();
        d.set(&now);

        // Uncomment below to update the time on the RTC clock chip;
        // You can then comment this out to continue fetching the latest time.
        // let _ = rv8803.update(rv8803::ClockData::new(), &Some(d)).unwrap();
    }

    info!("Starting loop()...");
    loop {
        pulse_heartbeat(
            |_| {
                // Connect to the RV8803 RTC and fetch the latest time.
                if let Some(d) = data {
                    match rv8803.now(d) {
                        Ok(mut data) => {
                            let data = rv8803::prelude::LoggableClockData::new(data);
                            info!("{}", data)
                        }
                        Err(err) => match err {
                            rv8803::prelude::DriverError::I2c(err) => {
                                error!("Unknown I2C error: {:?}", err)
                            }
                            _ => error!("Cannot fetch latest from RTC: Unknown error!"),
                        },
                    }
                } else {
                    error!("Clock data not provided!");
                }
            },
            (),
            led2,
        )
        .await;
    }
}

pub async fn pulse_heartbeat<F>(f: F, callback: (), led: &mut gpio::Output<'_>)
where
    F: FnOnce(()),
{
    // trace!("Heartbeat pulse...");

    led.set_high();
    Timer::after_millis(800).await;

    f(callback);

    led.set_low();
    Timer::after_millis(200).await;
}

You can also use a Raspberry Pi Pico (RP2040) to get started:

#[embassy_executor::main]
async fn main(spawner: Spawner) {
    let mut p = embassy_rp::init(Default::default());
    info!("Configure RP2040 for Skynet(TM) AI bootup. Muwahahahahhaha!");

    let mut led = Output::new(p.PIN_25, Level::Low);

    // I2C Setup
    info!("Starting I2C Setup");
    let sda = p.PIN_14; // Pico pin 16
    let scl = p.PIN_15; // Pico pin 17
    let mut i2c_config = I2cConfig::default();
    i2c_config.frequency = 400_000;
    let mut i2c = i2c::I2c::new_async(p.I2C1, scl, sda, Irqs, i2c_config);
    info!("I2C Initialized");

    // RV8803, default address 0x32h
    let mut rv8803: Driver<i2c::I2c<'_, I2C1, i2c::Async>, SevenBitAddress> = Driver::new(i2c);

    let mut data = Some(rv8803::ClockData::new());
    // let mut data: Option<ClockData> = None;

    if let Some(mut d) = data {
        let now = DateTimeBuilder::new()
            .year(CurrentYear::new(2024))
            .month(Month::October)
            .date(7)
            .weekday(Weekday::Monday)
            .hours(0)
            .minutes(0)
            .seconds(0)
            .build();
        d.set(&now);

        // Uncomment below to update the time on the RTC clock chip;
        // You can then comment this out to continue fetching the latest time.
        // let _ = rv8803.update(rv8803::ClockData::new(), &Some(d)).unwrap();
    }

    // ...
}

Refer to the docs for details.

Minimum supported Rust version (MSRV)

This project is tested against rust stable.

License

Licensed under either of Apache License Version 2.0 or The MIT License at your option.

🦀 ノ( º _ º ノ) - respect crables!

Copyright

Copyright © 2024, Michael de Silva