You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
I'm quite new to Modbus RTU protocol and I'm bit confused about the register addresses.
This is the data I read from Easton SDM72DM power meter with readInputRegisters(1,100) :
[
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
50108, 52674, 50059, 1730, 17030, 23989, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 50195, 7819, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 17903, 45703, 17826, 26757, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0
]
And here is a list of input registers for that power meter: https://xn--stromzhler-v5a.eu/media/pdf/93/17/d7/SDM72DM-V2.pdf
So my confusion is how the data I read relates to the addresses in the power meter ?
If I would like to read one register, let's say 30013 - Phase 1 active power, what parameters I should pass to readInputRegisters?
Thanks in advance for any help!
The text was updated successfully, but these errors were encountered:
I believe that for your example of reading 1 floating point value (not 1 register !), i.e. read "30013 - Phase 1 active power" the following parameters should be used readInputRegisters(12, 2).
In other words you should use the Modbus 'start' address (last two columns in your table) and required number of registers (keeping in mind that one floating point value occupies 2 Modbus RTU registers).
Hi,
I'm quite new to Modbus RTU protocol and I'm bit confused about the register addresses.
This is the data I read from Easton SDM72DM power meter with readInputRegisters(1,100) :
[
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
50108, 52674, 50059, 1730, 17030, 23989, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 50195, 7819, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 17903, 45703, 17826, 26757, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0,
0
]
And here is a list of input registers for that power meter:
https://xn--stromzhler-v5a.eu/media/pdf/93/17/d7/SDM72DM-V2.pdf
So my confusion is how the data I read relates to the addresses in the power meter ?
If I would like to read one register, let's say 30013 - Phase 1 active power, what parameters I should pass to readInputRegisters?
Thanks in advance for any help!
The text was updated successfully, but these errors were encountered: