You signed in with another tab or window. Reload to refresh your session.You signed out in another tab or window. Reload to refresh your session.You switched accounts on another tab or window. Reload to refresh your session.Dismiss alert
The new PropLoader outputs fewer and more clear messages with an optional message code.
Action
Include the new PropLoader in builds of SimpleIDE and issue the -c option with proploader.exe on the command so it outputs message codes. Capture these codes (for potential processing) but strip them from the output so users still see codeless message in the Build Status window. Messages with codes will always start with a 3-digit number followed immediately by a hyphen '-' making it easy to find codes, digest them, and strip them from messages. Format is ###-<text_message>.
NOTE: There may be some messages without leading codes, so it's important not to blindly strip the first four characters from the messages without first verifying that they are in the format ###-.
This new SimpleIDE feature is important to support Issue #261.
Background
There are three categories of messages and thus message codes:
Debugging/Verbose - These are mostly for seasoned developers (mainly us). They may express state information or specific deep error information that is usually only helpful to a small set of users, thus, they are never shown without an active -v option on the command line. These are all automatically given the code 000; tools that parse it should ignore all 000-coded messages.
Status - These express state/progress/event information and are given codes 001 through 099.
Error - These express fatal problems and are given codes 100 and beyond.
Code numbers will never be reused for a condition that means something different than that which was first assigned to a message.
Code numbers will never be reused for a condition that means something different than that which was first assigned to a message.
Top messages and their codes.
STATE/PROGRESS/EVENT
"001-Opening file %s", file
"002-Downloading to Propeller\n"
"003-Verifying RAM"
"004-Programming EEPROM"
"005-Download successful!"
"006-[ Entering terminal mode. Type ESC or Control-C to exit. ]"
"007-Writing %s to the SD card", file
"008-%ld bytes remaining"
"009-%ld bytes sent"
"010-Setting module name to %s"
ERRORS
"100-Option -n can only be used to name wifi modules\n"
"101-Invalid address: %s\n", ip_address
"102-Download failed: %d\n", sts
"103-Can't open file '%s'\n", file
"104-Propeller not found on port %s\n", port_or_ip_address
"105-Failed to enter terminal mode\n"
"106-Unrecognized wi-fi module firmware\n"
" Version is %s but expected %s.x...\n", wifiConnection->version(), WIFI_REQUIRED_MAJOR_VERSION
" Recommended action: update firmware and/or PropLoader to latest version(s).”
"107-Failed to write SD card file: '%s'\n", file
"108-Invalid module name\n"
"109-Failed to set module name\n"
The text was updated successfully, but these errors were encountered:
The new PropLoader outputs fewer and more clear messages with an optional message code.
Action
Include the new PropLoader in builds of SimpleIDE and issue the -c option with proploader.exe on the command so it outputs message codes. Capture these codes (for potential processing) but strip them from the output so users still see codeless message in the Build Status window. Messages with codes will always start with a 3-digit number followed immediately by a hyphen '-' making it easy to find codes, digest them, and strip them from messages. Format is ###-<text_message>.
NOTE: There may be some messages without leading codes, so it's important not to blindly strip the first four characters from the messages without first verifying that they are in the format ###-.
This new SimpleIDE feature is important to support Issue #261.
Background
There are three categories of messages and thus message codes:
Code numbers will never be reused for a condition that means something different than that which was first assigned to a message.
Code numbers will never be reused for a condition that means something different than that which was first assigned to a message.
Top messages and their codes.
STATE/PROGRESS/EVENT
"001-Opening file %s", file
"002-Downloading to Propeller\n"
"003-Verifying RAM"
"004-Programming EEPROM"
"005-Download successful!"
"006-[ Entering terminal mode. Type ESC or Control-C to exit. ]"
"007-Writing %s to the SD card", file
"008-%ld bytes remaining"
"009-%ld bytes sent"
"010-Setting module name to %s"
ERRORS
"100-Option -n can only be used to name wifi modules\n"
"101-Invalid address: %s\n", ip_address
"102-Download failed: %d\n", sts
"103-Can't open file '%s'\n", file
"104-Propeller not found on port %s\n", port_or_ip_address
"105-Failed to enter terminal mode\n"
"106-Unrecognized wi-fi module firmware\n"
" Version is %s but expected %s.x...\n", wifiConnection->version(), WIFI_REQUIRED_MAJOR_VERSION
" Recommended action: update firmware and/or PropLoader to latest version(s).”
"107-Failed to write SD card file: '%s'\n", file
"108-Invalid module name\n"
"109-Failed to set module name\n"
The text was updated successfully, but these errors were encountered: