Skip to content

Troubleshooting: Common Issues

Jump to bottom Edit New page
excalamus edited this page May 19, 2020 · 35 revisions

Some common problems and solutions are recorded here. If you're having a problem with Plover, see if it is described here along with a solution.

Also, please make sure to check the Plover bug tracker for known reported issues.

Running in Debug Mode

Windows

  1. Open Command Prompt or Powershell
  2. Navigate the Plover's installation folder where you can find plover.exe and plover_console.exe
  3. Type start plover_console.exe --log-level debug

Mac

  1. Open Terminal
  2. Assuming Plover in installed in your applications folder, enter this into Terminal and hit enter: /Applications/Plover.app/Contents/MacOS/Plover --log-level debug

Linux (AppImage)

  1. plover.AppImage --log-level debug

Issues

General

Plover does not recognize my USB keyboard or steno machine

Note: Initially, Plover is set up to use your computer keyboard as a steno machine. If you have a steno machine, you'll need to configure Plover to look for your machine. See the Supported Hardware page for configuration instructions specific to your machine.

If you know your machine has been configured correctly, and Plover doesn't recognize your keyboard or steno machine:

  1. Confirm your keyboard or steno machine is plugged into your computer.
  2. On the Plover control panel, check if it states the machine is connected or disconnected.
  • If it states the machine is disconnected, press the Reconnect button (this is to the right of "connected" or "disconnected" message).
  1. If Plover still doesn't recognize your machine, try closing and relaunching Plover.

Strokes no longer appear when using keyboard

If Plover is enabled with arpeggiating and strokes were previously registered, check that arpeggiating has not begun. Press <space> (by default) to toggle arpeggiate.

When using TX Bolt, any chord with SW- in it doesn't come out right

Solution: in the serial settings, uncheck "Xon/Xoff" under "Flow control". This will solve the issue where using S and W in a chord causes Plover to ignore those keys.

Dictionary issues

By default, Plover ships with three dictionaries: main.json, commands.json and user.json. This can be a source of confusion to new users.

Dictionary priority

If two dictionaries contain the same steno strokes, Plover will use the one in the dictionary that has the highest priority.

In Plover 3.x and below, the dictionaries in the dictionary list were prioritized from the bottom up.

In Plover 4 and above, the dictionaries order is configurable, but the default is to have the highest priority dictionary at the top, and it is labeled with a star ⭐.

By default, the user.json dictionary is placed at the highest priority. If you want new strokes to go to a different dictionary by default (for example, you have your own dictionary already), make sure that the target dictionary is the highest priority.

If you have your own dictionary already

If you have your own dictionary already, you'll probably want to remove main.json and custom.json and add your own dictionary. This includes existing stenographers and users of another theory (Magnum, Phoenix).

We do not recommend you remove the commands.json dictionary from the dictionary list. This is because Plover has some concepts that users of other steno software will not be familiar with initially. Feel free to go through commands.json, and remap strokes that you want to use in your own theory.

About the default dictionaries

main.json

main.json is the core default dictionary. It is based on Mirabai Knight's own personal dictionary, which follows a StenEd-style thoery. It contains over 140,000 entries and is adequate for anyone learning stenography. Mirabai uses this dictionary professionally for her realtime work.

commands.json

commands.json contains some keyboard shortcuts and Plover-specific utilities. For example, the stroke to add a new translation: TKUPT. It also contains arrow key movements, copy and paste, and more.

Have a look inside to see some sample keyboard commands that Plover can do.

user.json

user.json is a blank dictionary. By default, the user.json dictionary is the highest priority - it is the first dictionary Plover will use. When you define new strokes, they will get added to this dictionary. This means you can see which strokes you've defined yourself, instead of trying to locate them inside the default dictionaries.

Windows

Unrecognized keystrokes and other strange behavior

  • Disable AutoKey if you're getting strange behavior with Plover.

macOS

Plover does not run (macOS)

  • If you use a keyboard instead of a steno machine, Plover needs Assistive Device Permissions. From the Catalina version of macOS, you may need to enable both the Plover app and the env app under Security & Privacy > Privacy > Accessibility.
  • Plover will not work if you are using Karabiner Elements

Unrecognized keystrokes

macOS has a feature where holding down a key brings up an accent menu. This can sometimes drop keys when typing quickly, such as TO/FPLT producing t. instead of to. To disable this, follow the instructions in this article: "How to Disable the Character Accent Menu in OS X Mountain Lion".

Linux

Unrecognized keystrokes

  • Older versions of IBus (prior to 1.5.11) don't handle the very fast simulated key presses of Plover. If this issue affects you, make sure you disable IBus or upgrade it.

Linux dynamic keyboard layout switching is not working

  • Plover does not handle dynamic keyboard layout switching: see bug #298

Delayed/slow output when using gnome-shell and the keyboard machine

  • It's a gnome-shell bug, unfortunately there's no known workaround.

Plover Wiki — Open Steno Project — Plover Homepage

Plover

Stenography

The Steno Community

In-Browser Demo

Other Pages

Clone this wiki locally