Can't install

[sabatpoznan]

Hi,

I have files listed below on pendrive (FAT32 - tied 6 different):

openwrt-ar71xx-generic-cus531-16M-rootfs-squashfs.bin
openwrt-ar71xx-generic-cus531-16M-kernel.bin
GoHeishaMonConfig.new

eadonly=true Device="/dev/ttyUSB0" Loghex=true ReadInterval=1 Aquarea2mqttCompatible=false Aquarea2mqttPumpID="B0***-*****" Mqtt_topic_base="panasonic_heat_pump/main" Mqtt_set_base="panasonic_heat_pump/commands" ForceRefreshTime=300 MqttServer="1**.***.**.***" MqttPort="1883" MqttLogin="******" MqttPass="******" SleepAfterCommand=1 MqttClientID="GoHeishaMon-pub" MqttKeepalive=60 EnableCommand=true HAAutoDiscover=true

After 10-15s of pressing 3 buttons on TAW-CZ1 and middle led is changing colours, after a while it goes beak to blue and than starts flashing.

What am I doing wrong?

[adnovea]

Hi,
Installation hangs with center LED steady white

Everything goes well until CA-TAW1B reboot and the center LED lights white for ever.
After 5 mins, I removed the USB stick.
I can ping and connect the module using LuCI but neither MQTT nor SSH works.
It seems there is a configuration file issue, so I converted the GoHeishaMonConfig.new text file into UTF-8 just in case but w/o change.

I run Home Assistant on a RPi at IP:192.168.0.120 with Mosquitto broker and MQTT integration module.
My config is :

Readonly=true
Device="/dev/ttyUSB0"
Loghex=true
ReadInterval=1
Aquarea2mqttCompatible=false
Aquarea2mqttPumpID="XXXXX-XXXXX"   <-- Is the module ID required because sometimes I read that it should be left blank
Mqtt_topic_base="panasonic_heat_pump/main"
Mqtt_set_base="panasonic_heat_pump/commands"
ForceRefreshTime=300
MqttServer="192.168.0.120"
MqttPort="1883"
MqttLogin="xxxxxxx"
MqttPass="xxxxxxxx"
SleepAfterCommand=1
MqttClientID="GoHeishaMon-pub"
MqttKeepalive=60
EnableCommand=true
HAAutoDiscover=true

Thanks for your help

[adnovea]

[SOLVED with CZ-TAW1B module v04.03.01_007]

Many thanks to lsochanowski for the great job achieved.

I solved my GHM Version problem using the post #27 (comment)
My CZ-TAW1B runs with the GoHeishaMon 1.1.191z166 version but not with the 1.0.166.

NOTE: 
After depressing the 3 buttons more than 10 secs, the update starts and takes about 3 mins 
then the module reboot. When the LEDs were as described below, I removed the USB stick.
  POWER :  steady green
  STATUS : steady white 
  LINK :   slowly blink

STATUS ==> I got the MQQT and LuCI but no SSH working

I tried to enable SSH doing these steps:

1. EnableCommand=true in GoHeishaMonConfig.new
2. Publish topic "panasonic_heat_pump/commands/OSCommand (topic "panasonic_heat_pump/OSCommand" as mentioned in the post does not work)
3. Send one by one the 3 values: "umount /overlay" , "jffs2reset -y" and finally "reboot".

I left the USB drive with the configuration file in order to reload the config at reboot.
It worked because I modified the MQQT ReadInterval and confirmed the change.

For the 3 values above, panasonic_heat_pump/commands/OSCommand/out returns respectively:

out = -
out = /dev/mtdblock3 is not mounted, erasing it erasing 0 10000 erasing 10000 10000 erasing 20000 10000 erasing 30000 10000 erasing 40000 10000 erasing 50000 10000 erasing 60000 10000 erasing 70000 10000 -
out = - 

STATUS ==> I still have the MQTT but lost LuCI and SSH is not working.

I have issued some Linux commands using the OS topic to tackle this issue but everything seems ok :

netstat -p -l -t
Active Internet connections (only servers)
Proto Recv-Q Send-Q Local Address           Foreign Address         State       PID/Program name    
tcp        0      0 0.0.0.0:www             0.0.0.0:*               LISTEN      16569/uhttpd
tcp        0      0 0.0.0.0:ssh             0.0.0.0:*               LISTEN      1593/dropbear
tcp        0      0 :::ssh                  :::*                    LISTEN      1593/dropbear
 -

I solved my SSH problem in this post.

[A4urs]

Hi,
I also have a problem with installation.
I tried instaling latest relase and relase linked for newer hardware in instalation instructions.
Before doing anything led’s status:
T:Green
M:Blue
B:None
During pressing 3 buttons for ~10s
T:G
M:B
B:None
After pressing buttons for about 10s:
T:Green
M:Blinking blue
B:None
What may I be doing wrong?
Note: I havent connected Wi-Fi or ethernet to modlue but I don’t think that it would affect instalation.