forked from kylemsguy/memetest86
-
Notifications
You must be signed in to change notification settings - Fork 0
/
serial.h
163 lines (147 loc) · 6.11 KB
/
serial.h
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
/*
* include/linux/serial.h
*
* Copyright (C) 1992, 1994 by Theodore Ts'o.
*
* Redistribution of this file is permitted under the terms of the GNU
* Public License (GPL)
*
* These are the UART port assignments, expressed as offsets from the base
* register. These assignments should hold for any serial port based on
* a 8250, 16450, or 16550(A).
*/
#ifndef _LINUX_SERIAL_REG_H
#define _LINUX_SERIAL_REG_H
#define UART_RX 0 /* In: Receive buffer (DLAB=0) */
#define UART_TX 0 /* Out: Transmit buffer (DLAB=0) */
#define UART_DLL 0 /* Out: Divisor Latch Low (DLAB=1) */
#define UART_DLM 1 /* Out: Divisor Latch High (DLAB=1) */
#define UART_IER 1 /* Out: Interrupt Enable Register */
#define UART_IIR 2 /* In: Interrupt ID Register */
#define UART_FCR 2 /* Out: FIFO Control Register */
#define UART_EFR 2 /* I/O: Extended Features Register */
/* (DLAB=1, 16C660 only) */
#define UART_LCR 3 /* Out: Line Control Register */
#define UART_MCR 4 /* Out: Modem Control Register */
#define UART_LSR 5 /* In: Line Status Register */
#define UART_MSR 6 /* In: Modem Status Register */
#define UART_SCR 7 /* I/O: Scratch Register */
/*
* These are the definitions for the FIFO Control Register
* (16650 only)
*/
#define UART_FCR_ENABLE_FIFO 0x01 /* Enable the FIFO */
#define UART_FCR_CLEAR_RCVR 0x02 /* Clear the RCVR FIFO */
#define UART_FCR_CLEAR_XMIT 0x04 /* Clear the XMIT FIFO */
#define UART_FCR_DMA_SELECT 0x08 /* For DMA applications */
#define UART_FCR_TRIGGER_MASK 0xC0 /* Mask for the FIFO trigger range */
#define UART_FCR_TRIGGER_1 0x00 /* Mask for trigger set at 1 */
#define UART_FCR_TRIGGER_4 0x40 /* Mask for trigger set at 4 */
#define UART_FCR_TRIGGER_8 0x80 /* Mask for trigger set at 8 */
#define UART_FCR_TRIGGER_14 0xC0 /* Mask for trigger set at 14 */
/* 16650 redefinitions */
#define UART_FCR6_R_TRIGGER_8 0x00 /* Mask for receive trigger set at 1 */
#define UART_FCR6_R_TRIGGER_16 0x40 /* Mask for receive trigger set at 4 */
#define UART_FCR6_R_TRIGGER_24 0x80 /* Mask for receive trigger set at 8 */
#define UART_FCR6_R_TRIGGER_28 0xC0 /* Mask for receive trigger set at 14 */
#define UART_FCR6_T_TRIGGER_16 0x00 /* Mask for transmit trigger set at 16 */
#define UART_FCR6_T_TRIGGER_8 0x10 /* Mask for transmit trigger set at 8 */
#define UART_FCR6_T_TRIGGER_24 0x20 /* Mask for transmit trigger set at 24 */
#define UART_FCR6_T_TRIGGER_30 0x30 /* Mask for transmit trigger set at 30 */
/*
* These are the definitions for the Line Control Register
*
* Note: if the word length is 5 bits (UART_LCR_WLEN5), then setting
* UART_LCR_STOP will select 1.5 stop bits, not 2 stop bits.
*/
#define UART_LCR_DLAB 0x80 /* Divisor latch access bit */
#define UART_LCR_SBC 0x40 /* Set break control */
#define UART_LCR_SPAR 0x20 /* Stick parity (?) */
#define UART_LCR_EPAR 0x10 /* Even parity select */
#define UART_LCR_PARITY 0x08 /* Parity Enable */
#define UART_LCR_STOP 0x04 /* Stop bits: 0=1 stop bit, 1= 2 stop bits */
#define UART_LCR_WLEN5 0x00 /* Wordlength: 5 bits */
#define UART_LCR_WLEN6 0x01 /* Wordlength: 6 bits */
#define UART_LCR_WLEN7 0x02 /* Wordlength: 7 bits */
#define UART_LCR_WLEN8 0x03 /* Wordlength: 8 bits */
/*
* These are the definitions for the Line Status Register
*/
#define UART_LSR_TEMT 0x40 /* Transmitter empty */
#define UART_LSR_THRE 0x20 /* Transmit-hold-register empty */
#define UART_LSR_BI 0x10 /* Break interrupt indicator */
#define UART_LSR_FE 0x08 /* Frame error indicator */
#define UART_LSR_PE 0x04 /* Parity error indicator */
#define UART_LSR_OE 0x02 /* Overrun error indicator */
#define UART_LSR_DR 0x01 /* Receiver data ready */
/*
* These are the definitions for the Interrupt Identification Register
*/
#define UART_IIR_NO_INT 0x01 /* No interrupts pending */
#define UART_IIR_ID 0x06 /* Mask for the interrupt ID */
#define UART_IIR_MSI 0x00 /* Modem status interrupt */
#define UART_IIR_THRI 0x02 /* Transmitter holding register empty */
#define UART_IIR_RDI 0x04 /* Receiver data interrupt */
#define UART_IIR_RLSI 0x06 /* Receiver line status interrupt */
/*
* These are the definitions for the Interrupt Enable Register
*/
#define UART_IER_MSI 0x08 /* Enable Modem status interrupt */
#define UART_IER_RLSI 0x04 /* Enable receiver line status interrupt */
#define UART_IER_THRI 0x02 /* Enable Transmitter holding register int. */
#define UART_IER_RDI 0x01 /* Enable receiver data interrupt */
/*
* These are the definitions for the Modem Control Register
*/
#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
#define UART_MCR_OUT2 0x08 /* Out2 complement */
#define UART_MCR_OUT1 0x04 /* Out1 complement */
#define UART_MCR_RTS 0x02 /* RTS complement */
#define UART_MCR_DTR 0x01 /* DTR complement */
/*
* These are the definitions for the Modem Status Register
*/
#define UART_MSR_DCD 0x80 /* Data Carrier Detect */
#define UART_MSR_RI 0x40 /* Ring Indicator */
#define UART_MSR_DSR 0x20 /* Data Set Ready */
#define UART_MSR_CTS 0x10 /* Clear to Send */
#define UART_MSR_DDCD 0x08 /* Delta DCD */
#define UART_MSR_TERI 0x04 /* Trailing edge ring indicator */
#define UART_MSR_DDSR 0x02 /* Delta DSR */
#define UART_MSR_DCTS 0x01 /* Delta CTS */
#define UART_MSR_ANY_DELTA 0x0F /* Any of the delta bits! */
/*
* These are the definitions for the Extended Features Register
* (StarTech 16C660 only, when DLAB=1)
*/
#define UART_EFR_CTS 0x80 /* CTS flow control */
#define UART_EFR_RTS 0x40 /* RTS flow control */
#define UART_EFR_SCD 0x20 /* Special character detect */
#define UART_EFR_ENI 0x10 /* Enhanced Interrupt */
/*
* the low four bits control software flow control
*/
#include "io.h"
#define serial_echo_outb(v,a) outb((v),(a)+serial_base_ports[serial_tty])
#define serial_echo_inb(a) inb((a)+serial_base_ports[serial_tty])
#define BOTH_EMPTY (UART_LSR_TEMT | UART_LSR_THRE)
/* Wait for transmitter & holding register to empty */
#define WAIT_FOR_XMITR \
do { \
lsr = serial_echo_inb(UART_LSR); \
} while ((lsr & BOTH_EMPTY) != BOTH_EMPTY)
#if 0
static inline void serial_echo(int ch)
{
int lsr;
WAIT_FOR_XMITR;
serial_echo_outb(ch, UART_TX);
}
static inline void serial_debug(int ch)
{
serial_echo(ch);
serial_echo('\r');
serial_echo('\n');
}
#endif
#endif /* _LINUX_SERIAL_REG_H */