forked from scottbez1/smartknob
-
Notifications
You must be signed in to change notification settings - Fork 0
/
platformio.ini
121 lines (112 loc) · 3.63 KB
/
platformio.ini
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
; PlatformIO Project Configuration File
;
; Build options: build flags, source filter
; Upload options: custom upload port, speed and extra flags
; Library options: dependencies, extra library storages
; Advanced options: extra scripting
;
; Please visit documentation for the other options and examples
; https://docs.platformio.org/page/projectconf.html
[platformio]
default_envs = view
src_dir = firmware/src
lib_dir = firmware/lib
include_dir = firmware/include
test_dir = firmware/test
data_dir = firmware/data
[base_config]
platform = [email protected]
framework = arduino
monitor_speed = 921600
monitor_flags =
--eol=CRLF
--echo
--filter=esp32_exception_decoder
lib_deps =
askuric/Simple FOC @ 2.2.0
infineon/TLV493D-Magnetic-Sensor @ 1.0.3
bxparks/AceButton @ 1.9.1
build_flags =
-DCORE_DEBUG_LEVEL=ARDUHAL_LOG_LEVEL_DEBUG
-DMONITOR_SPEED=921600
[env:view]
extends = base_config
board = esp32doit-devkit-v1
lib_deps =
${base_config.lib_deps}
bodmer/[email protected]
fastled/FastLED @ 3.5.0
bogde/HX711 @ 0.7.5
adafruit/Adafruit VEML7700 Library @ 1.1.1
bakercp/PacketSerial @ 1.4.0
nanopb/Nanopb @ 0.4.6 ; Ideally this would reference the nanopb submodule, but that would require
; everyone to check out submodules to just compile, so we use the library
; registry for the runtime. The submodule is available for manually updating
; the pre-compiled (checked in) .pb.h/c files when proto files change, but is
; otherwise not used during application firmware compilation.
build_flags =
${base_config.build_flags}
; Display enabled: 1=enable, 0=disable
-DSK_DISPLAY=1
; Display orientation: 0=usb bottom, 2=usb top
-DSK_DISPLAY_ROTATION=0
; LEDs enabled: 1=enable, 0=disable
-DSK_LEDS=1
; Number of LEDs
-DNUM_LEDS=8
-DSENSOR_MT6701=1
; Strain-gauge press input enabled: 1=enable, 0=disable
-DSK_STRAIN=1
; Invert direction of angle sensor (motor direction is detected relative to angle sensor as part of the calibration procedure)
-DSK_INVERT_ROTATION=1
; Ambient light sensor (VEML7700) enabled: 1=enable (display/LEDs match ambient brightness), 0=disable (100% brightness all the time)
-DSK_ALS=1
; Pin configurations
-DPIN_UH=26
-DPIN_UL=25
-DPIN_VH=27
-DPIN_VL=32
-DPIN_WH=12
-DPIN_WL=33
-DPIN_BUTTON_NEXT=-1
-DPIN_BUTTON_PREV=-1
-DPIN_SDA=15
-DPIN_SCL=8
-DPIN_MT_DATA=37
-DPIN_MT_CLOCK=13
-DPIN_MT_CSN=14
-DPIN_LED_DATA=7
-DPIN_LCD_BACKLIGHT=19
-DDESCRIPTION_FONT=Roboto_Thin_24
-DDESCRIPTION_Y_OFFSET=20
-DVALUE_OFFSET=30
-DDRAW_ARC=0
; TFT_eSPI setup
-DUSER_SETUP_LOADED=1
-DGC9A01_DRIVER=1
-DCGRAM_OFFSET=1
-DTFT_WIDTH=240
-DTFT_HEIGHT=240
-DTFT_MISO=-1
-DTFT_MOSI=5
-DTFT_SCLK=20
-DTFT_CS=21
-DTFT_DC=22
-DTFT_RST=4
-DTFT_BL=-1
-DLOAD_GLCD=1
-DLOAD_GFXFF=1
-DSPI_FREQUENCY=40000000
; Reduce loop task stack size (only works on newer IDF Arduino core)
; -DARDUINO_LOOP_STACK_SIZE=2048
; FastLED setup
; Modify the default unusable pin mask to allow GPIO 7 (allowed to use on ESP32-PICO-V3-02)
; Unusable bits: 6, 8, 9, 10, 20
; (0ULL | _FL_BIT(6) | _FL_BIT(8) | _FL_BIT(9) | _FL_BIT(10) | _FL_BIT(20))
-DFASTLED_UNUSABLE_PIN_MASK=0x100740LL
; 0~39 except from 24, 28~31 are valid
; (0xFFFFFFFFFFULL & ~(0ULL | _FL_BIT(24) | _FL_BIT(28) | _FL_BIT(29) | _FL_BIT(30) | _FL_BIT(31)))
-DSOC_GPIO_VALID_GPIO_MASK=0xFF0EFFFFFF
; GPIO >= 34 are input only
; (SOC_GPIO_VALID_GPIO_MASK & ~(0ULL | _FL_BIT(34) | _FL_BIT(35) | _FL_BIT(36) | _FL_BIT(37) | _FL_BIT(38) | _FL_BIT(39)))
-DSOC_GPIO_VALID_OUTPUT_GPIO_MASK=0x30EFFFFFF