Home Assistant OS 14.0

[sairon]

Home Assistant Operating System

• Bump Buildroot to 2024.02.7 (Bump Buildroot to 2024.02.7 #3659) @sairon
• Remove unnecessary kernel post-install hook for GRUB-based targets (Remove unnecessary kernel post-install hook for GRUB-based targets #3672) @sairon
• Reduce timeout for network time synchronization to 15 seconds (Reduce timeout for network time synchronization to 15 seconds #3669) @sairon
• Enable Cypress M8 USB serial driver for all targets (Enable Cypress M8 USB serial driver for all targets #3693) @sairon

Raspberry Pi

• Add Hailo-8 firmware for Raspberry Pi AI Kit/HAT on RPi 5 (Add Hailo-8 firmware for Raspberry Pi AI Kit/HAT on RPi 5 #3680) @sairon
• RaspberryPi: Update kernel to 6.6.51 - stable_20241008 (RaspberryPi: Update kernel to 6.6.51 - stable_20241008 #3662) @sairon
• Disable UAS via usb-storage.quirks on RPi for JMicron JMS583 (Disable UAS via usb-storage.quirks on RPi for JMicron JMS583 #3687) @RubenKelevra

Home Assistant Yellow

• Add initial support for Raspberry Pi CM5 on Yellow (Add initial support for Raspberry Pi CM5 on Yellow #3667) @sairon
• RaspberryPi: Update kernel to 6.6.51 - stable_20241008 (RaspberryPi: Update kernel to 6.6.51 - stable_20241008 #3662) @sairon
• Always use NVMe datadisk on Yellow if it's present on first boot (Always use NVMe datadisk on Yellow if it's present on first boot #3686) @sairon

Home Assistant Green

• Linux: Update kernel to 6.6.63 (Linux: Update kernel to 6.6.63 #3697) @sairon

Open Virtual Appliance

• Add iwlwifi-gl firmware needed for Intel BE200 Wi-Fi 7 card (Add iwlwifi-gl firmware needed for Intel BE200 Wi-Fi 7 card #3668) @antst
• Add kernel config to support external i2c devices (Add kernel config to support external i2c devices #3642) @xtsrthm
• Add kernel options required for Atheros 12k wirelss adapters (Add kernel options required for Atheros 12k wirelss adapters #3640) @agners
• Linux: Update kernel to 6.6.62 (Linux: Update kernel to 6.6.62 #3679) @sairon

Generic x86-64

• Add iwlwifi-gl firmware needed for Intel BE200 Wi-Fi 7 card (Add iwlwifi-gl firmware needed for Intel BE200 Wi-Fi 7 card #3668) @antst
• Add kernel options required for Atheros 12k wirelss adapters (Add kernel options required for Atheros 12k wirelss adapters #3640) @agners
• Linux: Update kernel to 6.6.63 (Linux: Update kernel to 6.6.63 #3697) @sairon

Hardkernel ODROID

• Fall back to max eMMC clock to fix Kingston eMMC compat with ODROID-N2 (Fall back to max eMMC clock to fix Kingston eMMC compat with ODROID-N2 #3665) @sairon
• Linux: Update kernel to 6.6.63 (Linux: Update kernel to 6.6.63 #3697) @sairon

ASUS Tinker

• Linux: Update kernel to 6.6.63 (Linux: Update kernel to 6.6.63 #3697) @sairon

Khadas VIM Series

• Linux: Update kernel to 6.6.63 (Linux: Update kernel to 6.6.63 #3697) @sairon

Generic aarch64

• Add iwlwifi-gl firmware needed for Intel BE200 Wi-Fi 7 card (Add iwlwifi-gl firmware needed for Intel BE200 Wi-Fi 7 card #3668) @antst
• Linux: Update kernel to 6.6.63 (Linux: Update kernel to 6.6.63 #3697) @sairon

Build System

• Add Kconfig option for Supervisor channel (Add Kconfig option for Supervisor channel #3618) @agners
• Bump docker/build-push-action from 6.9.0 to 6.10.0 (Bump docker/build-push-action from 6.9.0 to 6.10.0 #3704) @dependabot

---

This discussion was created from the release Home Assistant OS 14.0.

[pcmike]

Attempting to update an HAOS VM that previously when updating to 13.2 would get stuck on "target reached: system reboot" but would boot into 13.2 update if rebooted manually (and would subsequently reboot just fine from cli "host reboot") and now updating to 14 it's stuck this time at "Unmounting HassOS data partition..." :(

Threw in the towel and rolled back to my snapshot. I have no clue what's going on with these HAOS updates, but they're not applying cleanly since 13.2.

[RubenKelevra]

@pcmike if you haven't can you open an issue and attach the output of blkid from the system console (use login to get OS shell access).

how can you actually get into the console? using novnc console from proxmox doesn't allow you to copy&paste and installing the ssh add-on and logging in via web ui or even regular ssh just drops you into some sort of environment that doesn't even have access to blkid. It just gives you access to "ha" and that doesn't get you into the actual system?

You need to disable the "Protection mode", to access the host via the add-on.

blkid will then still show no output, however you can list the ids via:

ls -l /dev/disk/by-uuid/ 

and for the list of mounts:

cat /proc/mounts

[RubenKelevra]

@Ladenburg1 / @RGarrett93 I'm running a Raspberry Pi 4B via USB-NVMe Storage - no issues here, so it's not a general issue, but something specific of your setup. I think it would be better to create new issues for the trouble you're having with all the details of your systems, like the type of SSD, the converter you're using etc.

[danwooller]

Mine hung but after a reboot came back at 14.0

[Ladenburg1]

Im using a NVMe-storage connected by a PCIe to NVMe SSD Shield (hat). It's an itenso 256 GB NVMe.
Trisd to update to 14 again with no success, hungs and after hard reboot it comes back with 13.2

[ctulhua]

Same here with RPi5 and nvme hat. Update 13.2 to 14 comes with success, but:
➜ ~ ha os info
board: rpi5-64
boot: A
boot_slots:
A:
state: booted
status: good
version: "13.2"
B:
state: inactive
status: bad
version: "14.0"
data_disk: TS1TMTE400S-I777670289
update_available: true
version: "13.2"
version_latest: "14.0"

[bearhntr]

Are there any plans to add the INTEL Bluetooth support? For example the AX210/211 which is Wi-Fi 6E with Bluetooth. More specifically for HAOS under Proxmox as a VM.

[Anto79-ops]

There are no issues on my NUC 12 (x86-64, bare-metal) with USB SkyConnect and USB Aeotec Z-Stick 7.

The system is running normally.

[thezfunk]

Anyone on a Pi 4 with a Z-wave USB stick want to volunteer to see if the boot loop issue is fixed? Still on 11.5 with mine.

[Skuair]

I have a Pi3 with zigbee dongle-p and I had the boot loop issue since OS 12.4 only when host started with dongle plugged and zigbee2mqtt auto start. The workaround with the config.txt and dtoverlay=dwc2 worked for me.

[cristianstoica]

No issues with updating from 13.2 to 14.0 on RPi4.

[thezfunk]

Do you have a Z-wave USB stick?

[brugk000]

HP T630 no issues updating to HAOS14

[AndyFlysJabs]

I'm on 13.2, can see the update to 14.0 listed and have tried to upgrade 3 times. In all cases It hasn't occurred, but a full restart of the server it's on has occurred and I can't see anything in the system logs that infers an upgrade/update has failed. At the Home Assistant Command line I can see its still 13.2

How can I find useful info that I can use to help you/me identify what the issue is?

I'm running the X86 image on an old Gen 8 HP Microserver.

Regards

Andy

[AndyFlysJabs]

Is the fact that I need to currently use GRUB2 to Allow and old HP Microserver to boot into 13.2 likely to be the cause of the 14 update failure....

[joro-home]

Same problem. Not able to upgrade HA OS 13.2 to 14. Also using GRUB2. Who can help me with a solution?

[Guruleenyc]

I just upgraded successfully on an x86 Lenovo m73

[joro-home]

I just upgraded successfully on an x86 Lenovo m73

Also using Grub2? Or does it have a UEFI BIOS?

[joro-home]

As a new HA user I didn't know I had to select the boot-slot B manually. All works fine now.

[pwirkus]

Hello, my problem is as follows, I have an RPI5 8GB with an NVME disk and the update is successful, but after some time no ZigBee network works, all devices are not visible and I cannot enter the console as well as HACS and add-ons, then I have to turn off the power and wait until the system will load, I open the terminal and enter ha os update --version 13.2 and then everything works fine. I also cannot access the logs despite the message saying: the system says Error while loading pagr logs. Any advice on what could be wrong?