-
Notifications
You must be signed in to change notification settings - Fork 795
/
MPI4008-show
executable file
·105 lines (97 loc) · 3.49 KB
/
MPI4008-show
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
#!/bin/bash
sudo ./system_backup.sh
#root_dev=`grep -oPr "root=[^\s]*" /boot/cmdline.txt | awk -F= '{printf $NF}'`
#if test "$root_dev" = "/dev/mmcblk0p7";then
#sudo cp -rf ./boot/config-noobs-nomal.txt ./boot/config.txt.bak
#else
#sudo cp -rf ./boot/config-nomal.txt ./boot/config.txt.bak
#sudo echo "hdmi_force_hotplug=1" >> ./boot/config.txt.bak
#fi
source ./system_config.sh
if [ $hardware_model -eq 5 ]; then
sudo sed -i -e 's/#dtoverlay=vc4-kms-v3d/dtoverlay=vc4-kms-v3d/' ./boot/config.txt.bak
fi
sudo echo "hdmi_force_hotplug=1" >> ./boot/config.txt.bak
sudo echo "hdmi_force_edid_audio=1" >> ./boot/config.txt.bak
sudo echo "dtparam=i2c_arm=on" >> ./boot/config.txt.bak
sudo echo "dtparam=spi=on" >> ./boot/config.txt.bak
sudo echo "enable_uart=1" >> ./boot/config.txt.bak
sudo echo "display_rotate=3" >> ./boot/config.txt.bak
sudo echo "max_usb_current=1" >> ./boot/config.txt.bak
sudo echo "config_hdmi_boost=7" >> ./boot/config.txt.bak
sudo echo "hdmi_group=2" >> ./boot/config.txt.bak
sudo echo "hdmi_mode=1" >> ./boot/config.txt.bak
sudo echo "hdmi_mode=87" >> ./boot/config.txt.bak
sudo echo "hdmi_drive=2" >> ./boot/config.txt.bak
sudo echo "hdmi_cvt 480 800 60 6 0 0 0" >> ./boot/config.txt.bak
sudo echo "dtoverlay=ads7846,cs=1,penirq=25,penirq_pull=2,speed=50000,keep_vref_on=0,swapxy=0,pmax=255,xohms=150,xmin=200,xmax=3900,ymin=200,ymax=3900" >> ./boot/config.txt.bak
sudo cp -rf ./boot/config.txt.bak /boot/config.txt
if [ $hardware_model -eq 5 ]; then
sudo sed -i "/xrandr -o/d" /etc/xdg/lxsession/LXDE-pi/autostart
sudo echo "xrandr -o 1" >> /etc/xdg/lxsession/LXDE-pi/autostart
fi
#sudo cp -rf ./boot/config-397.txt /boot/config.txt
#if test "$root_dev" = "/dev/mmcblk0p7";then
#sudo cp ./usr/cmdline.txt-noobs /boot/cmdline.txt
#else
#sudo cp ./usr/cmdline.txt /boot/
#fi
sudo cp ./usr/inittab /etc/
if [[ "$deb_version" < "12.1" ]]; then
sudo cp -rf ./usr/99-fbturbo.conf-HDMI /usr/share/X11/xorg.conf.d/99-fbturbo.conf
fi
if [ ! -d /etc/X11/xorg.conf.d ]; then
sudo mkdir /etc/X11/xorg.conf.d
fi
sudo cp -rf ./usr/99-calibration.conf-397-270 /etc/X11/xorg.conf.d/99-calibration.conf
sudo touch ./.have_installed
echo "hdmi:resistance:397:270:480:800" > ./.have_installed
#nodeplatform=`uname -n`
#kernel=`uname -r`
version=`uname -v`
#if test "$nodeplatform" = "raspberrypi";then
#echo "this is raspberrypi kernel"
input_result=0
version=${version##* }
#version=${version#*#}
echo $version
if test $version -lt 2017;then
echo "reboot"
else
echo "need to update touch configuration"
wget --spider -q -o /dev/null --tries=1 -T 10 http://mirrors.zju.edu.cn/raspbian/raspbian
if [ $? -ne 0 ]; then
input_result=1
else
sudo apt-get install xserver-xorg-input-evdev 2> error_output.txt
dpkg -l | grep xserver-xorg-input-evdev > /dev/null 2>&1
if [ $? -ne 0 ]; then
input_result=1
fi
fi
if [ $input_result -eq 1 ]; then
if [ $hardware_arch -eq 32 ]; then
sudo dpkg -i -B ./xserver-xorg-input-evdev_1%3a2.10.6-1+b1_armhf.deb 2> error_output.txt
elif [ $hardware_arch -eq 64 ]; then
sudo dpkg -i -B ./xserver-xorg-input-evdev_1%3a2.10.6-2_arm64.deb 2> error_output.txt
fi
fi
result=`cat ./error_output.txt`
echo -e "\033[31m$result\033[0m"
grep -q "error:" ./error_output.txt && exit
sudo cp -rf /usr/share/X11/xorg.conf.d/10-evdev.conf /usr/share/X11/xorg.conf.d/45-evdev.conf
#echo "reboot"
fi
#else
#echo "this is not raspberrypi kernel, no need to update touch configure, reboot"
#fi
sudo sync
sudo sync
sleep 1
if [ $# -eq 1 ]; then
sudo ./rotate.sh $1
elif [ $# -gt 1 ]; then
echo "Too many parameters"
fi
echo "reboot now"
sudo reboot