Skip to content

Latest commit

 

History

History
640 lines (494 loc) · 26.8 KB

README.md

File metadata and controls

640 lines (494 loc) · 26.8 KB
Raw

ansible-role-wireguard

This Ansible role is used in my blog series Kubernetes the not so hard way with Ansible but can be used standalone of course. I use WireGuard and this Ansible role to setup a fully meshed VPN between all nodes of my little Kubernetes cluster.

In general WireGuard is a network tunnel (VPN) for IPv4 and IPv6 that uses UDP. If you need more information about WireGuard you can find a good introduction here: Installing WireGuard, the Modern VPN.

Linux

This role should work with:

  • Ubuntu 20.04 (Focal Fossa)
  • Ubuntu 22.04 (Jammy Jellyfish)
  • Archlinux
  • Debian 11 (Bullseye)
  • Debian 12 (Bookworm)
  • Fedora 37
  • Fedora 38
  • CentOS 7
  • AlmaLinux 8
  • AlmaLinux 9
  • Rocky Linux 8
  • Rocky Linux 9
  • openSUSE Leap 15.4
  • openSUSE Leap 15.5
  • Oracle Linux 9

Best effort:

  • elementary OS 6

Molecule tests are available (see further down below). It should also work with Raspbian Buster but for this one there is no test available. MacOS (see below) should also work partitially but is only best effort.

MacOS

While this playbook configures, enables and starts a systemd service on Linux in a such a way that no additional action is needed, on MacOS it installs the required packages and it just generates the correct wg0.conf file that is then placed in the specified wireguard_remote_directory (/opt/local/etc/wireguard by default). In order to run the VPN, then, you need to:

sudo wg-quick up wg0

and to deactivate it

sudo wg-quick down wg0

or you can install the official app and import the wg0.conf file.

Versions

I tag every release and try to stay with semantic versioning. If you want to use the role I recommend to checkout the latest tag. The master branch is basically development while the tags mark stable releases. But in general I try to keep master in good shape too.

Requirements

By default port 51820 (protocol UDP) should be accessible from the outside. But you can adjust the port by changing the variable wireguard_port. Also IP forwarding needs to be enabled e.g. via echo 1 > /proc/sys/net/ipv4/ip_forward. I decided not to implement this task in this Ansible role. IMHO that should be handled elsewhere. You can use my ansible-role-harden-linux e.g. Besides changing sysctl entries (which you need to enable IP forwarding) it also manages firewall settings among other things. Nevertheless the PreUp, PreDown, PostUp and PostDown hooks may be a good place to do some network related stuff before a WireGuard interface comes up or goes down.

Changelog

Change history:

See full CHANGELOG.md

Changes in the last two versions:

15.0.0

Breaking:

  • removed support for Ubuntu 18.04 (reached end of life)
  • removed support for Fedora 36 (reached end of life)

Feature:

  • add support for Fedora 37
  • add support for Fedora 38
  • add support for openSUSE 15.5
  • add support for Debian 12
  • prefix host name comment with Name = for wg-info in WireGuard interface configuration (contribution by @tarag)

Molecule:

  • rename kvm scenario to default
  • rename kvm-single-server scenario to single-server
  • upgrade OS and reboot in prepare before converge for Almalinux

Other:

  • fix ansible-lint issues

14.0.0

Breaking:

  • CentOS 7: Introduce wireguard_centos7_kernel_plus_reboot and wireguard_centos7_standard_reboot variables. Both are set to "true" by default. This will cause the host to be rebooted in case the "wireguard" kernel module was installed the very fir st time. If wireguard_centos7_installation_method: "kernel-plus" is set and the host wasn't booted with a kernel-plus kernel already you most probably need to reboot. For the standard kernel this might not be needed.
  • CentOS 7: Add reboot to the standard mode to make sure the WireGuard kernel module is available (contribution by @mofelee)
  • Introduce wireguard_update_cache variable to control if package manager caches should be updated before the installation (contribution by @sebix). Before this release the package manager cache wasn't updated for AlmaLinux 9, Archlinux, Fedora and openSUSE. With wireguard_update_cache set to true by default those OSes are now also update the package manager cache. If you don't want that set wireguard_update_cache to false for the host in question.

Feature:

  • add support for Oracle Linux 9 (contribution by @cola-zero)

Deprecation:

  • variable wireguard_ubuntu_update_cache is deprecated

Installation

  • Directly download from Github (change into Ansible role directory before cloning): git clone https://github.com/githubixx/ansible-role-wireguard.git githubixx.ansible_role_wireguard

  • Via ansible-galaxy command and download directly from Ansible Galaxy: ansible-galaxy install role githubixx.ansible_role_wireguard

  • Create a requirements.yml file with the following content (this will download the role from Github) and install with ansible-galaxy role install -r requirements.yml:

---
roles:
  - name: githubixx.ansible_role_wireguard
    src: https://github.com/githubixx/ansible-role-wireguard.git
    version: 15.0.0

Role Variables

These variables can be changed in group_vars/ e.g.:

# Directory to store WireGuard configuration on the remote hosts
wireguard_remote_directory: "/etc/wireguard"              # On Linux
# wireguard_remote_directory: "/opt/local/etc/wireguard"  # On MacOS

# The default port WireGuard will listen if not specified otherwise.
wireguard_port: "51820"

# The default interface name that WireGuard should use if not specified otherwise.
wireguard_interface: "wg0"

# The default owner of the wg.conf file
wireguard_conf_owner: root

# The default group of the wg.conf file
wireguard_conf_group: "{{ 'root' if not ansible_os_family == 'Darwin' else 'wheel' }}"

# The default mode of the wg.conf file
wireguard_conf_mode: 0600

# Whether any change to the wg.conf file should be backup
wireguard_conf_backup: false

# The default state of the wireguard service
wireguard_service_enabled: "yes"
wireguard_service_state: "started"

# By default "wg syncconf" is used to apply WireGuard interface settings if
# they've changed. Older WireGuard tools doesn't provide this option. In that
# case as a fallback the WireGuard interface will be restarted. This causes a
# short interruption of network connections.
#
# So even if "false" is the default, the role figures out if the "syncconf"
# option of the "wg" utility is available and if not falls back to "true"
# (which means interface will be restarted as this is the only possible option
# in this case).
#
# Possible options:
# - false (default)
# - true
#
# Both options have their pros and cons. The default "false" option (do not
# restart interface)
# - does not need to restart the WireGuard interface to apply changes
# - does not cause a short VPN connection interruption when changes are applied
# - might cause network routes are not properly reloaded
#
# Setting the option value to "true" will
# - restart the WireGuard interface as the name suggests in case of changes
# - cause a short VPN connection interruption when changes are applied
# - make sure that network routes are properly reloaded
#
# So it depends a little bit on your setup which option works best. If you
# don't have an overly complicated routing that changes very often or at all
# using "false" here is most properly good enough for you. E.g. if you just
# want to connect a few servers via VPN and it normally stays this way.
#
# If you have a more dynamic routing setup then setting this to "true" might be
# the safest way to go. Also if you want to avoid the possibility creating some
# hard to detect side effects this option should be considered.
wireguard_interface_restart: false

# Normally the role automatically creates a private key the very first time
# if there isn't already a WireGuard configuration. But this option allows
# to provide your own WireGuard private key if really needed. As this is of
# course a very sensitive value you might consider a tool like Ansible Vault
# to store it encrypted.
# wireguard_private_key:

# Set to "false" if package cache should not be updated (only relevant if
# the package manager in question supports this option)
wireguard_update_cache: "true"

# Normally the role installs and activates the wireguard kernel module where
# appropriate.  In some cases we might not be able load kernel modules, like
# unprivileged LXC guests.  If you set this to false you have to ensure
# the wireguard module is available in the kernel!
wireguard_install_kernel_module: true

There are also a few Linux distribution specific settings:

#######################################
# Settings only relevant for:
# - Ubuntu
# - elementary OS
#######################################

# DEPRECATED: Please use "wireguard_update_cache" instead.
# Set to "false" if package cache should not be updated.
wireguard_ubuntu_update_cache: "{{ wireguard_update_cache }}"

# Set package cache valid time
wireguard_ubuntu_cache_valid_time: "3600"

#######################################
# Settings only relevant for CentOS 7
#######################################

# Set wireguard_centos7_installation_method to "kernel-plus"
# to use the kernel-plus kernel, which includes a built-in,
# signed WireGuard module.
#
# The default of "standard" will use the standard kernel and
# the ELRepo module for WireGuard.
wireguard_centos7_installation_method: "standard"

# Reboot host if necessary if the "kernel-plus" kernel is in use
wireguard_centos7_kernel_plus_reboot: true

# The default seconds to wait for machine to reboot and respond
# if "kernel-plus" is in use. Is only relevant if
# "wireguard_centos7_kernel_plus_reboot" is set to "true".
wireguard_centos7_kernel_plus_reboot_timeout: "600"

# Reboot host if necessary if the standard kernel is in use
wireguard_centos7_standard_reboot: true

# The default seconds to wait for machine to reboot and respond
# if "standard" kernel is in use. Is only relevant if
# "wireguard_centos7_standard_reboot" is set to "true".
wireguard_centos7_standard_reboot_timeout: "600"

#########################################
# Settings only relevant for RockyLinux 8
#########################################

# Set wireguard_rockylinux8_installation_method to "dkms"
# to build WireGuard module from source, with wireguard-dkms.
# This is required if you use a custom kernel and/or your arch
# is not x86_64.
#
# The default of "standard" will install the kernel module
# with kmod-wireguard from ELRepo.
wireguard_rockylinux8_installation_method: "standard"

Every host in host_vars/ should configure at least one address via wireguard_address or wireguard_addresses. The wireguard_address can only contain one IPv4, thus it's recommended to use the wireguard_addresses variable that can contain an array of both IPv4 and IPv6 addresses.

wireguard_addresses:
  - "10.8.0.101/24"

Of course all IP's should be in the same subnet like /24 we see in the example above. If wireguard_allowed_ips is not set then the default values are IPs defined in wireguard_address and wireguard_addresses without the CIDR but instead with /32 (IPv4) or /128 (IPv6) which is basically a host route (have a look templates/wg.conf.j2). Let's see this example and let's assume you don't set wireguard_allowed_ips explicitly:

[Interface]
Address = 10.8.0.2/24
PrivateKey = ....
ListenPort = 51820

[Peer]
PublicKey = ....
AllowedIPs = 10.8.0.101/32
Endpoint = controller01.p.domain.tld:51820

This is part of the WireGuard config from my workstation. It has the VPN IP 10.8.0.2 and we've a /24 subnet in which all my WireGuard hosts are located. Also you can see we've a peer here that has the endpoint controller01.p.domain.tld:51820. When wireguard_allowed_ips is not explicitly set the Ansible template will add an AllowedIPs entry with the IP of that host plus /32 or /128. In WireGuard this basically specifies the routing. The config above says: On my workstation with the IP 10.8.0.2 I want send all traffic to 10.8.0.101/32 to the endpoint controller01.p.domain.tld:51820. Now let's assume we set wireguard_allowed_ips: "0.0.0.0/0". Then the resulting config looks like this.

[Interface]
Address = 10.8.0.2/24
PrivateKey = ....
ListenPort = 51820

[Peer]
PublicKey = ....
AllowedIPs = 0.0.0.0/0
Endpoint = controller01.p.domain.tld:51820

Now this is basically the same as above BUT now the config says: I want to route EVERY traffic originating from my workstation to the endpoint controller01.p.domain.tld:51820. If that endpoint can handle the traffic is of course another thing and it's up to you how you configure the endpoint routing ;-)

You can specify further optional settings (they don't have a default and won't be set if not specified besides wireguard_allowed_ips as already mentioned) also per host in host_vars/ (or in your Ansible hosts file if you like). The values for the following variables are just examples and no defaults (for more information and examples see wg-quick.8):

wireguard_allowed_ips: ""
wireguard_endpoint: "host1.domain.tld"
wireguard_persistent_keepalive: "30"
wireguard_dns: "1.1.1.1"
wireguard_fwmark: "1234"
wireguard_mtu: "1492"
wireguard_table: "5000"
wireguard_preup:
  - ...
wireguard_predown:
  - ...
wireguard_postup:
  - ...
wireguard_postdown:
  - ...
wireguard_save_config: "true"

wireguard_(preup|predown|postup|postdown) are specified as lists. Here are two examples:

wireguard_postup:
  - iptables -t nat -A POSTROUTING -o ens12 -j MASQUERADE
  - iptables -A FORWARD -i %i -j ACCEPT
  - iptables -A FORWARD -o %i -j ACCEPT
wireguard_preup:
  - echo 1 > /proc/sys/net/ipv4/ip_forward
  - ufw allow 51820/udp

The commands are executed in order as described in wg-quick.8.

Additionally one can add "unmanaged" peers. Those peers are not handled by Ansible and not part of the vpn Ansible host group e.g.:

wireguard_unmanaged_peers:
  client.example.com:
    public_key: 5zsSBeZZ8P9pQaaJvY9RbELQulcwC5VBXaZ93egzOlI=
    # preshared_key: ... e.g. from ansible-vault?
    allowed_ips: 10.0.0.3/32
    endpoint: client.example.com:51820
    persistent_keepalive: 0

One of wireguard_address (deprecated) or wireguard_addresses (recommended) is required as already mentioned. It's the IPs of the interface name defined with wireguard_interface variable (wg0 by default). Every host needs at least one unique VPN IP of course. If you don't set wireguard_endpoint the playbook will use the hostname defined in the vpn hosts group (the Ansible inventory hostname). If you set wireguard_endpoint to "" (empty string) that peer won't have a endpoint. That means that this host can only access hosts that have a wireguard_endpoint. That's useful for clients that don't expose any services to the VPN and only want to access services on other hosts. So if you only define one host with wireguard_endpoint set and all other hosts have wireguard_endpoint set to "" (empty string) that basically means you've only clients besides one which in that case is the WireGuard server. The third possibility is to set wireguard_endpoint to some hostname. E.g. if you have different hostnames for the private and public DNS of that host and need different DNS entries for that case setting wireguard_endpoint becomes handy. Take for example the IP above: wireguard_address: "10.8.0.101". That's a private IP and I've created a DNS entry for that private IP like host01.i.domain.tld (i for internal in that case). For the public IP I've created a DNS entry like host01.p.domain.tld (p for public). The wireguard_endpoint needs to be a interface that the other members in the vpn group can connect to. So in that case I would set wireguard_endpoint to host01.p.domain.tld because WireGuard normally needs to be able to connect to the public IP of the other host(s).

Here is a litte example for what I use the playbook: I use WireGuard to setup a fully meshed VPN (every host can directly connect to every other host) and run my Kubernetes (K8s) cluster at Hetzner Cloud (but you should be able to use any hoster you want). So the important components like the K8s controller and worker nodes (which includes the pods) only communicate via encrypted WireGuard VPN. Also (as already mentioned) I've two clients. Both have kubectl installed and are able to talk to the internal Kubernetes API server by using WireGuard VPN. One of the two clients also exposes a WireGuard endpoint because the Postfix mailserver in the cloud and my internal Postfix needs to be able to talk to each other. I guess that's maybe a not so common use case for WireGuard :D But it shows what's possible. So let me explain the setup which might help you to use this Ansible role.

First, here is a part of my Ansible hosts file:

[vpn]
controller0[1:3].i.domain.tld
worker0[1:2].i.domain.tld
server.at.home.i.domain.tld
workstation.i.domain.tld

[k8s_controller]
controller0[1:3].i.domain.tld

[k8s_worker]
worker0[1:2].i.domain.tld

As you can see I've three groups here: vpn (all hosts on that will get WireGuard installed), k8s_controller (the Kubernetes controller nodes) and k8s_worker (the Kubernetes worker nodes). The i in the domainname is for internal. All the i.domain.tld DNS entries have a A record that points to the WireGuard IP that we define shortly for every host e.g.: controller01.i.domain.tld. IN A 10.8.0.101. The reason for that is that all Kubernetes components only binds and listen on the WireGuard interface in my setup. And since I need this internal IPs for all my Kubernetes components I specify the internal DNS entries in my Ansible hosts file. That way I can use the Ansible inventory hostnames and variables very easy in the playbooks and templates.

For the Kubernetes controller nodes I've defined the following host variables:

Ansible host file: host_vars/controller01.i.domain.tld

---
wireguard_addresses:
  - "10.8.0.101/24"
wireguard_endpoint: "controller01.p.domain.tld"
ansible_host: "controller01.p.domain.tld"
ansible_python_interpreter: /usr/bin/python3

Ansible host file: host_vars/controller02.i.domain.tld:

---
wireguard_addresses:
  - "10.8.0.102/24"
wireguard_endpoint: "controller02.p.domain.tld"
ansible_host: "controller02.p.domain.tld"
ansible_python_interpreter: /usr/bin/python3

Ansible host file: host_vars/controller03.i.domain.tld:

---
wireguard_addresses:
  - "10.8.0.103/24"
wireguard_endpoint: "controller03.p.domain.tld"
ansible_host: "controller03.p.domain.tld"
ansible_python_interpreter: /usr/bin/python3

I've specified ansible_python_interpreter here for every node as the controller nodes use Ubuntu 18.04 which has Python 3 installed by default. ansible_host is set to the public DNS of that host. Ansible will use this hostname to connect to the host via SSH. I use the same value also for wireguard_endpoint because of the same reason. The WireGuard peers needs to connect to the other peers via a public IP (well at least via a IP that the WireGuard hosts can connect to - that could be of course also a internal IP if it works for you). IPs specified by wireguard_address or wireguard_addresses needs to be unique of course for every host.

For the Kubernetes worker I've defined the following variables:

Ansible host file: host_vars/worker01.i.domain.tld

---
wireguard_addresses:
  - "10.8.0.111/24"
wireguard_endpoint: "worker01.p.domain.tld"
wireguard_persistent_keepalive: "30"
ansible_host: "worker01.p.domain.tld"
ansible_python_interpreter: /usr/bin/python3

Ansible host file: host_vars/worker02.i.domain.tld:

---
wireguard_addresses:
  - "10.8.0.112/24"
wireguard_endpoint: "worker02.p.domain.tld"
wireguard_persistent_keepalive: "30"
ansible_host: "worker02.p.domain.tld"
ansible_python_interpreter: /usr/bin/python3

As you can see the variables are basically the same as the controller nodes have with one exception: wireguard_persistent_keepalive: "30". My worker nodes (at Hetzner Cloud) and my internal server (my server at home) are connected because I've running Postfix at my cloud nodes and the external Postfix server forwards the received mails to my internal server (and vice versa). I needed the keepalive setting because from time to time the cloud instances and the internal server lost connection and this setting solved the problem. The reason for this is of course because my internal server is behind NAT and the firewall/router must keep the NAT/firewall mapping valid (NAT and Firewall Traversal Persistence).

For my internal server at home (connected via DSL router to the internet) we've this configuration:

---
wireguard_addresses:
  - "10.8.0.1/24"
wireguard_endpoint: "server.at.home.p.domain.tld"
wireguard_persistent_keepalive: "30"
ansible_host: 192.168.2.254
ansible_port: 22

By default the SSH daemon is listening on a different port than 22 on all of my public nodes but internally I use 22 and that's the reason to set ansible_port: 22 here. Also ansible_host is of course a internal IP for that host. The wireguard_endpoint value is a dynamic DNS entry. Since my IP at home isn't static I need to run a script every minute at my home server that checks if the IP has changed and if so adjusts my DNS record. I use OVH's DynHost feature to accomplish this but you can use and DynDNS provider you want of course. Also I forward incoming traffic on port 51820/UDP to my internal server to allow incoming WireGuard traffic. IPs from wireguard_address and wireguard_addresses needs to be of course part of our WireGuard subnet.

And finally for my workstation (on which I run all ansible-playbook commands):

wireguard_addresses:
  - "10.8.0.2/24"
wireguard_endpoint: ""
ansible_connection: local
ansible_become: false

As you can see wireguard_endpoint: "" is a empty string here. That means the Ansible role won't set an endpoint for my workstation. Since there is no need for the other hosts to connect to my workstation it doesn't makes sense to have a endpoint defined. So in this case I can access all hosts defined in the Ansible group vpn from my workstation but not the other way round. So the resulting WireGuard config for my workstation looks like this:

[Interface]
Address = 10.8.0.2/24
PrivateKey = ....
ListenPort = 51820

[Peer]
PublicKey = ....
AllowedIPs = 10.8.0.101/32
Endpoint = controller01.p.domain.tld:51820

[Peer]
PublicKey = ....
AllowedIPs = 10.8.0.102/32
Endpoint = controller02.p.domain.tld:51820

[Peer]
PublicKey = ....
AllowedIPs = 10.8.0.103/32
Endpoint = controller03.p.domain.tld:51820

[Peer]
PublicKey = ....
AllowedIPs = 10.8.0.111/32
PersistentKeepalive = 30
Endpoint = worker01.p.domain.tld:51820

[Peer]
PublicKey = ....
AllowedIPs = 10.8.0.112/32
PersistentKeepalive = 30
Endpoint = worker02.p.domain.tld:51820

[Peer]
PublicKey = ....
AllowedIPs = 10.8.0.1/32
PersistentKeepalive = 30
Endpoint = server.at.home.p.domain.tld:51820

The other WireGuard config files (wg0.conf by default) looks similar but of course [Interface] includes the config of that specific host and the [Peer] entries lists the config of the other hosts.

Example Playbooks

- hosts: vpn
  roles:
    - githubixx.ansible_role_wireguard
  hosts: vpn
  roles:
    -
      role: githubixx.ansible_role_wireguard
      tags: role-wireguard

Example inventory using two different WireGuard interfaces on host "multi"

This is a complex example using yaml inventory format:

vpn1:
  hosts:
    multi:
      wireguard_addresses:
        - "10.9.0.1/32"
      wireguard_allowed_ips: "10.9.0.1/32, 192.168.2.0/24"
      wireguard_endpoint: multi.example.com
    nated:
      wireguard_addresses:
        - "10.9.0.2/32"
      wireguard_allowed_ips: "10.9.0.2/32, 192.168.3.0/24"
      wireguard_persistent_keepalive: 15
      wireguard_endpoint: nated.example.com
      wireguard_postup:
        - iptables -t nat -A POSTROUTING -o ens12 -j MASQUERADE
        - iptables -A FORWARD -i %i -j ACCEPT
        - iptables -A FORWARD -o %i -j ACCEPT
      wireguard_postdown:
        - iptables -t nat -D POSTROUTING -o ens12 -j MASQUERADE
        - iptables -D FORWARD -i %i -j ACCEPT
        - iptables -D FORWARD -o %i -j ACCEPT

vpn2:
  hosts:
    # Use a different name, and define ansible_host, to avoid mixing of vars without
    # needing to prefix vars with interface name.
    multi-wg1:
      ansible_host: multi
      wireguard_interface: wg1
      # when using several interface on one host, we must use different ports
      wireguard_port: 51821
      wireguard_addresses:
        - "10.9.1.1/32"
      wireguard_endpoint: multi.example.com
    another:
      wireguard_address:
        - "10.9.1.2/32"
      wireguard_endpoint: another.example.com

Sample playbooks for example above:

- hosts: vpn1
  roles:
    - githubixx.ansible_role_wireguard
- hosts: vpn2
  roles:
    - githubixx.ansible_role_wireguard

Testing

This role has a small test setup that is created using Molecule, libvirt (vagrant-libvirt) and QEMU/KVM. Please see my blog post Testing Ansible roles with Molecule, libvirt (vagrant-libvirt) and QEMU/KVM how to setup. The test configuration is here.

Afterwards molecule can be executed:

molecule converge

This will setup quite a few virtual machines (VM) with different supported Linux operating systems. To run a few tests:

molecule verify

To clean up run

molecule destroy

There is also a small Molecule setup that mimics a central WireGuard server with a few clients:

molecule converge -s single-server

License

GNU General Public License v3.0 or later

Author Information

http://www.tauceti.blog