lr3

\mainpage Main Page

---

LR 3 Click

LR 3 Click is a compact add-on board that contains a long-range transceiver. This board features the 32001345, RF technology-based SRD transceiver, which operates at a frequency of 868MHz from Mipot.

Click Product page

---

Click library

• Author : MikroE Team
• Date : jun 2020.
• Type : UART type

Software Support

We provide a library for the LR3 Click as well as a demo application (example), developed using MikroElektronika compilers. The demo can run on all the main MikroElektronika development boards.

Package can be downloaded/installed directly form compilers IDE(recommended way), or downloaded from our LibStock, or found on mikroE github account.

Library Description

This library contains API for LR3 Click driver.

Standard key functions :

• Config Object Initialization function.

void lr3_cfg_setup ( lr3_cfg_t *cfg );

• Initialization function.

LR3_RETVAL lr3_init ( lr3_t *ctx, lr3_cfg_t *cfg );

Example key functions :

• Function performs the recovery of EEPROM default values.

LR3_RETVAL lr3_factory_reset ( lr3_t *ctx );

• Function writes data to EEPROM.

LR3_RETVAL lr3_write_eeprom ( lr3_t *ctx, uint8_t address, uint8_t n_bytes, uint8_t *data_in );

• Function performs the transmission of radio frames.

LR3_RETVAL lr3_tx_message ( lr3_t *ctx, lr3_tx_msg_t *tx_msg );

Examples Description

This example reads and processes data from LR 3 clicks.

The demo application is composed of two sections :

Application Init

Initializes the driver, enables the Click board and configures it for the selected mode.

void application_init ( void )
{
    log_cfg_t log_cfg;
    lr3_cfg_t cfg;

    /** 
     * Logger initialization.
     * Default baud rate: 115200
     * Default log level: LOG_LEVEL_DEBUG
     * @note If USB_UART_RX and USB_UART_TX 
     * are defined as HAL_PIN_NC, you will 
     * need to define them manually for log to work. 
     * See @b LOG_MAP_USB_UART macro definition for detailed explanation.
     */
    LOG_MAP_USB_UART( log_cfg );
    log_init( &logger, &log_cfg );
    log_info( &logger, "---- Application Init ----" );

    //  Click initialization.

    lr3_cfg_setup( &cfg );
    LR3_MAP_MIKROBUS( cfg, MIKROBUS_1 );
    lr3_init( &lr3, &cfg );

    Delay_ms ( 100 );
    lr3_set_ind_handler( &lr3, indication_handler );
    lr3_hard_reset( &lr3 );
    lr3_factory_reset( &lr3 );
    Delay_ms ( 1000 );
    
#ifdef MASTER
    // Set device as MASTER
    tmp_msg.payload[ 0 ] = 0;

    if( lr3_write_eeprom( &lr3, 0x00, 1, &tmp_msg.payload[ 0 ] ) )
    {
        log_error( &logger, "Setting device as MASTER!\r\n" );
        for( ; ; );
    }
    
    log_printf( &logger, "Device configured as MASTER!\r\n" );
    Delay_ms ( 1000 );
    
    // Delete all network table
    if( lr3_delete_all_network_table( &lr3 ) )
    {
        log_error( &logger, "Deleting all paired devices!\r\n" );
        for( ; ; );
    }
    log_printf( &logger, "All paired devices deleted!\r\n" );
    Delay_ms ( 1000 );
    
    // Enable pairing
    if( lr3_enable_pairing( &lr3, 1 ) )
    {
        log_error( &logger, "Pairing not enabled!\r\n" );
        for( ; ; );
    }
    log_printf( &logger, "Pairing enabled!\r\n" );
    Delay_ms ( 1000 );
#endif

#ifdef END_NODE
    // Set device as END_NODE
    tmp_msg.payload[ 0 ] = 1;
    
    if( lr3_write_eeprom( &lr3, 0x00, 1, &tmp_msg.payload[ 0 ] ) )
    {
        log_error( &logger, "Setting device as END_NODE!\r\n" );
        for( ; ; );
    }
    
    log_printf( &logger, "Device configured as END_NODE!\r\n" );
    Delay_ms ( 1000 );
    
    // Send pairing request and displays MASTER ID
    uint8_t master_id[ 4 ] = { 0 };
    do
    {
        lr3_get_pairing_request( &lr3 );
        Delay_ms ( 1000 );
    }
    while ( lr3_get_activation_status( &lr3, master_id ) != 1 );
    log_printf( &logger, "Paired to a network!\r\n" );
    log_printf( &logger, "Master ID: 0x%.2X%.2X%.2X%.2X\r\n", ( uint16_t ) master_id[ 3 ],
                                                              ( uint16_t ) master_id[ 2 ],
                                                              ( uint16_t ) master_id[ 1 ],
                                                              ( uint16_t ) master_id[ 0 ] );
    
#endif
}
  

Application Task

Depending on the selected mode, it reads all the received data or sends a desired message every 3 seconds. All data is being displayed on the USB UART.

void application_task ( void )
{
#ifdef END_NODE
    strcpy( tmp_msg.payload, TEXT_TO_SEND );
   
    lr3_tx_msg.data_in = &tmp_msg.payload[ 0 ];
    lr3_tx_msg.n_bytes = strlen( TEXT_TO_SEND );
    lr3_tx_msg.destination_id = LR3_BROADCAST_MESSAGE;
    lr3_tx_msg.option = LR3_UNCONFIRMED_DATA_TX;
    if ( lr3_tx_message( &lr3, &lr3_tx_msg ) == 0 )
    {
        log_printf( &logger, "Message: \"%s\" sent to MASTER...\r\n", ( uint8_t * ) TEXT_TO_SEND );
        log_printf( &logger, "------------------------\r\n" );
    }
    
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
    Delay_ms ( 1000 );
#endif
#ifdef MASTER
    lr3_read_message_process( &lr3 );
#endif 
} 

The full application code, and ready to use projects can be installed directly form compilers IDE(recommneded) or found on LibStock page or mikroE GitHub accaunt.

Other mikroE Libraries used in the example:

• MikroSDK.Board
• MikroSDK.Log
• Click.LR3

Additional notes and informations

Depending on the development board you are using, you may need USB UART Click, USB UART 2 Click or RS232 Click to connect to your PC, for development systems with no UART to USB interface available on the board. The terminal available in all Mikroelektronika compilers, or any other terminal application of your choice, can be used to read the message.

---