graphlcd.conf

# graphlcd.conf.sample
#
# This file contains a sample configuration for the graphlcd driver
# library.
#
# The format is ini-file-like. It is divided into sections that start
# at markers that look like [section]. Comments are all line-based
# comments, and are lines that start with '#'.
#
# The file starts with general settings, that are used by several
# drivers, followed by the sections. Each section represents a single
# display with a driver definition and specific settings which define
# how the driver acts. Some of these parameters like device, port and
# size are already parsed by the library but the drivers can also read
# their own options from the config file. The library passes them to
# the drivers.

# WaitMethod
#  Select the method that is used for sleeping.
#  Possible values:
#   0 - usleep
#   1 - nanosleep
#   2 - nanosleep (sched_rr) - This is recommended on kernel 2.4 systems
#   3 - gettimeofday - This is recommended on kernel 2.6 systems
#  Default value: 3
WaitMethod=3

# WaitPriority
#  Select the process priority that is used when sleeping.
#  Possible values: -20 <= x <= 19
#  Default value: 0
WaitPriority=0

# General driver settings
#  This section lists the display settings that are parsed and
#  recognized by the driver library.
#
# Driver
#  Sets the display's driver.
#  Currently available are: framebuffer, gu140x32f, gu256x64-372,
#                           gu256x64C-3xx0, hd61830, image, ks0108,
#                           sed1520, sed1330, simlcd, t6963c,
#                           gu126x64D-K610A4
#
# Device
#  Instead of using the direct output via port address (see Port), you
#  can use the parport device (/dev/parportX). The advantage over the
#  direct output via port address is that this works for non-root users
#  also. But it's a little bit slower. The modules ppdev.o, parport.o
#  and parport_pc.o must be loaded or compiled into the kernel.
#
# Port
#  Sets the port address of the parallel port. If this parameter is not
#  given, 0x378 is used. To use this direct output, the program that
#  uses the driver library has to be started with user 'root'.
#
# Width
#  Sets the horizontal size of the display. If this parameter is not
#  given, a default one specific to the driver is used.
#
# Height
#  Sets the vertical size of the display. If this parameter is not
#  given, a default one specific to the driver is used.
#
# UpsideDown
#  Rotates the display output by 180 degrees. This might be useful, if
#  the LCD is mounted upside-down.
#  Possible values: 'yes', 'no'
#  Default value: 'no'
#
# Invert
#  Inverts the display.
#  Possible values: 'yes', 'no'
#  Default value: 'no'
#
# Brightness
#  Sets the brightness of your display's backlight if supported by its
#  driver.
#  Supported by: gu140x32f, gu256x64-372, gu256x64-3900, gu126x64D-K610A4, ax206dpf
#  Possible values: 0 <= x <= 100)
#  Default value: 100
#
# Contrast
#  Sets the contrast of your display if supported by its driver.
#  Supported by: serdisplib
#  Possible values: 0 <= x <= 10
#  Default value: 5
#
# Backlight
#  Switches the backlight of your display on and off if supported by
#  its driver.
#  Supported by: serdisplib
#  Possible values: 'yes', 'no'
#  Default value: 'yes'
#
# AdjustTiming
#  To get a timing that is as accurate as possible, the drivers measure
#  the time for port commands (see: benchmark in syslog). You might
#  decrease or increase the time to wait after port commands with this
#  parameter. Normally, there is no need to change this parameter.
#  (used by gu140x32f, gu256x64-372, gu256x64-3900, hd61830, ks0108,
#   sed1330, sed1520, gu126x64D-K610A4, noritake800)
#  Possible values: -50 <= x <= 50
#  Default value: 0
#
# RefreshDisplay
#  Normally, most of the drivers do not update the whole display, but
#  only the areas that have changed since last update. So it might be,
#  that some faulty pixels would stay a longer time. To avoid this, the
#  plugin makes a complete refresh from time to time. This parameter
#  defines how often a complete refresh will be done.
#  e.g.: A value of 5 means, that the plugin will make a complete
#        refresh on every 5th update.
#  A value of 0 completely disables complete refreshs.
#  Possible values: 0 <= x <= 50
#  Default value: 5

########################################################################

[framebuffer]
# framebuffer driver
#  Output goes to a framebuffer device
Driver=framebuffer

#UpsideDown=no
#Invert=no

# Device
#  Framebuffer device
#  Default value: /dev/fb0
#Device=/dev/fb0

# Damage | ReportDamage
#  Damage reporting for framebuffer devices with update problems
#  Possible values: none, auto, udlfb, ugly
#    none:  no damage reporting
#    auto:  automatic determination if damage reporting is needed
#    udlfb: damage reporting for udlfb-devices (displaylink)
#    ugly:  dirty damagereporting (a '\n' is written to the framebuffer file handle)
#  Default value: none
#Damage=none

# Zoom
#  Determines if pixels should be drawn double sized.
#  If zoom is set, the actual resolution will be halved (both width and height)
#  e.g.: framebuffer has resolution 800x600: this driver will report a drawing area of 400x300
#  Possible values: 0, 1
#  Default value: 1
Zoom=1

########################################################################

[gu140x32f]
# gu140x32f driver
#  This is an 8-bit driver module for Noritake GU140x32-F7806 VFD
#  displays. The VFD is operating in it's 8 bit-mode connected to a
#  single PC parallel port.
#  Default size: 140 x 32
Driver=gu140x32f

Device=/dev/parport0
#Port=0x378
#Width=140
#Height=32
#UpsideDown=no
#Invert=no
#Brightness=100
#AdjustTiming=0
#RefreshDisplay=1

# Wiring
#  Select the type of wiring your display is connected with.
#  Possible values: 'Standard', 'Windows'
#  Default value: 'Standard'
Wiring=Standard

########################################################################

[gu256x64-372]
# gu256x64-372 driver
#  This is an 8-bit driver module for Noritake GU256x64-372 VFD
#  displays. The VFD is operating in it's 8 bit-mode connected to a
#  single PC parallel port.
#  Default size: 256 x 64
Driver=gu256x64-372

Device=/dev/parport0
#Port=0x378
#Width=256
#Height=64
#UpsideDown=no
#Invert=no
#Brightness=100
#AdjustTiming=0
#RefreshDisplay=1

# Wiring
#  Select the type of wiring your display is connected with.
#  Possible values: 'Standard', 'Windows'
#  Default value: 'Standard'
Wiring=Standard

########################################################################

[gu256x64-3900]
# gu256x64-3900 driver
#  This is a driver module for Noritake GU256X64x-3900 VFD displays. The
#  VFD is either operating in 8 bit-mode connected to a single PC
#  parallel port or in serial mode connected to a single PC serial port.
#  Default size: 256 x 64
Driver=gu256x64-3900

Device=/dev/parport0
#Port=0x378
#Width=256
#Height=64
#UpsideDown=no
#Invert=no
#Brightness=100
#AdjustTiming=0
#RefreshDisplay=1

# Wiring
#  Select the type of wiring your display is connected with.
#  Possible values: 'Standard', 'Satyr'
#  Default value: 'Standard'
Wiring=Standard

# Interface
#  Select the interface your display is connnected to.
#  Possible values: 'Parallel', 'Serial'
#  Default value: 'Parallel'
Interface=Parallel

# DMA
#  Enables/disables the usage of the controller's DMA mode which
#  increases writing speed. This only works in parallel interface mode.
#  Possible values: 'yes', 'no'
#  Default value: 'yes'
DMA=yes

########################################################################

[gu126x64D-K610A4]
# GU126x64D-K610A4 driver
#  This is a driver module for Noritake GU126x64D-K610A4 VFD displays.
#  The VFD is operating in 8 bit-mode connected to a single PC
#  parallel port.
#  Default size: 126 x 64
Driver=gu126x64D-K610A4

Device=/dev/parport0
#Port=0x378
#Width=126
#Height=64
#UpsideDown=no
#Invert=no
#Brightness=100
#RefreshDisplay=1
#AdjustTiming=30

#  Debug some methods of the driver
#  (add the values of interest)
#
#   1: show a log at the start of a refresh
#   2: show a log at the end of a refresh with timing information
#   4: show the rows (8 pixel) refreshed
#   8: show every commands/bytes sent to the display
#  16: log every unsuccessful waiting for display acknowledge
#
#Debug=0

########################################################################

[hd61830]
# hd61830 driver
#  This is a driver module for the Hitachi HD61830 LCD controller.
#  Default size: 240 x 128
Driver=hd61830

Device=/dev/parport0
#Port=0x378
#Width=240
#Height=128
#UpsideDown=no
#Invert=no
#AdjustTiming=0
#RefreshDisplay=1

########################################################################

[image]
# image driver
#  This is a driver module for writing image sequences in PBM (Portable
#  Bit Map) format that show the plugin's output.
#  Default size: 240 x 128
Driver=image
#Width=240
#Height=128
#UpsideDown=no
#Invert=no

########################################################################

[ks0108]
# ks0108 driver
#  This is a driver module for the Samsung KS0108 LCD controller.
#  Default size: 128 x 64
Driver=ks0108

Device=/dev/parport0
#Port=0x378
Width=128
#Width=192
#Height=64
#UpsideDown=no
#Invert=no
#AdjustTiming=0
#RefreshDisplay=1

# Control
#  Select the variant of triggering the display's control lines.
#  Possible values: '0', '1'
#  Default value: '1'
Control=1

########################################################################

[sed1330]
# sed1330 driver
#  This is a driver module for the Epson SED1330/1335 LCD controller.
#  Default size: 320 x 240
Driver=sed1330

Device=/dev/parport0
#Port=0x378
#Width=320
#Height=240
#UpsideDown=no
#Invert=no
#AdjustTiming=0
#refreshDisplay=1

# Wiring
#  Select the type of wiring your display is connected with.
#  Possible values: 'Original', 'PowerLCD', 'LCDProc', 'Tweakers',
#                   'YASEDW'
#  Default value: 'Original'
Wiring=Original

# OscillatorFrequency
#  Select the frequency the oscillator on your LCD board uses in kHz.
#  Possible values: 1000 <= x <= 15000)
#  Default value: 9600
OscillatorFrequency=9600

# Interface
#  Select the interface mode your display is connected with.
#  Possible values: '6800', '8080'
#  Default value: '6800'
Interface=6800

########################################################################

[sed1520]
# sed1520 driver
#  This is a driver module for the Epson SED1520 LCD controller.
#  Default size: 120 x 32
Driver=sed1520

Device=/dev/parport0
#Port=0x378
#Width=120
#Height=32
#UpsideDown=no
#Invert=no
#AdjustTiming=0
#RefreshDisplay=1

########################################################################

[simlcd]
# simlcd driver
#  This is the SimLCD driver module. Output goes to a file instead of
#  LCD. Use SimLCD tool to view this file.
#  Default size: 240 x 128
Driver=simlcd
#Width=240
#Height=128
#UpsideDown=no
#Invert=no

########################################################################

[t6963c]
# t6963c driver
#  This is a driver module for the Toshiba T6963C LCD controller.
#  Default size: 240 x 128
Driver=t6963c

Device=/dev/parport0
#Port=0x378
#Width=240
#Height=128
#UpsideDown=no
#Invert=no
#RefreshDisplay=1

# Wiring
#  Select the type of wiring your display is connected with.
#  Possible values: 'Standard', 'Windows', 'Serial'
#  Default value: 'Standard'
Wiring=Standard

# FontSelect
#  Select the font width your display uses for text mode. In most cases
#  this is selectable through one of the pins of your LCD board
#  Possible values: '6', '8'
#  Default value: '6'
FontSelect=6

# AutoMode
#  Enables or disables the usage of T6963C's auto mode which doubles
#  writing speed when enabled.
#  Possible values: 'yes', 'no'
#  Default value: 'yes'
AutoMode=yes

# StatusCheck
#  Enables or disables the usage of T6963C's status check. When using a
#  shielded cable for connecting your display, the disabling may be
#  possible. This results in doubling the speed of writing data to the
#  LCD.
#  Possible values: 'yes', 'no'
#  Default value: 'yes'
StatusCheck=yes

########################################################################

[serdisp]
Driver=serdisp
# Controller
#  Select the serdisplib name of your display.
#  Possible values: See README in serdisplib package or http://serdisplib.sourceforge.net
#Controller=nokia7110
#Controller=sed1335
Controller=optrex323
#Controller=l4m132c
#Controller=l4m320t

# Options
#  Pass display specific options
#  Possible values: See driver-specific hardware page at http://serdisplib.sourceforge.net
#
#  IMPORTANT: when using generic controllers like sed1330,sed1335,t6963c, width and height
#             need to be set here (if different from default settings)!
#             (serdisplib needs to be extended to be able to use 'Width' and 'Height'
#              settings directly - this will be added later)
#
#Options=MODE=8080
#Options=DELAY=2000;FONTWIDTH=8;CHECK=1
#Options=WIDTH=128;HEIGHT=64
#Options=WIDTH=128;HEIGHT=64;DELAY=2000;FONTWIDTH=8;CHECK=1

# Wiring
#  Select Wiring
#  Possible values: See driver-specific hardware page at http://serdisplib.sourceforge.net
#Wiring=1
#Wiring=PowerLCD
#Wiring=DATA8,CS:nAUTO,A0:INIT,WR:nSTRB,RD:nSELIN

# FGColour
#  Drawing colour for non-monochrome displays
#  Possible values: 0xRRGGBB (eg.: 0xFF0000)
#  Defaults to black (0x000000) if not set
#FGColour=0x000000

# BGColour
#  Background colour for non-monochrome displays
#  Possible values: 0xRRGGBB (eg.: 0x00FFFF)
#  Defaults to white (0xFFFFFF) if not set
#BGColour=0xFFFFFF

Device=/dev/parport0
#Port=0x378
#Device=HID:/dev/usb/hiddev0
#Device=HID:/dev/hiddev0
#Device=USB:USB:4243/ee20 # Linux4Media 320T TouchLCD
#UpsideDown=no
#Invert=no
Contrast=5
Backlight=yes

# Settings 'Width' and 'Height' are ignored at the moment. For generic controllers # (sed1330/1335, t6963) width and height need to be set using setting 'Options' (look above)
##Width=240
##Height=128

########################################################################

[noritake800]
# noritake800 driver
#  This is an 8-bit driver module for Noritake Noritake 800(A) series VFD
#  displays. The VFD is operating in it's 8 bit-mode connected to a
#  single PC parallel port.
#  Default size: 128 x 64
Driver=noritake800

Device=/dev/parport0
#Port=0x378
Width=128
Height=64
#UpsideDown=no
#Invert=no
Brightness=50
AdjustTiming=50
RefreshDisplay=50

# Wiring
#  Select the type of wiring your display is connected with.
#  Possible values: 'LiquidMp3', 'MZ'
#  Default value: 'LiquidMp3'
Wiring=LiquidMp3

########################################################################

[avrctl]
# avrctl driver
#  This is an driver module for my AVR controlled LCD display connected via
#  USB port. It uses some simple commands to update the display content.
#  Default size: 256 x 128
Driver=avrctl
Device=/dev/ttyUSB0
Width=256
Height=128
#UpsideDown=no
#Invert=no
Brightness=50
RefreshDisplay=1

########################################################################

[g15daemon]
# pseudo device for the g15daemon meta driver
# Output goes to the g15daemon which then displays it
Driver=g15daemon
Width=160
Height=43

########################################################################

[network]
# network driver
#  Default size: 240 x 128
Driver=network
Width=256
Height=128
UpsideDown=no
Invert=no
Brightness=10
RefreshDisplay=1

########################################################################

[dm140gink]
#  dm140gink driver
#  This is an driver module for Futaba DM140-GINK VFD displays.
#  The VFD is built-in in some HTPC cases and connected to a
#  USB port.
#  Default size: 112 x 16
Driver=dm140gink
#Width=112
#Height=16
#UpsideDown=no

# Invertion is not supported
#Invert=no

# USB VendorID and ProductID
#Vendor=0x040b
#Product=0x7001
# USB ID activy 5xx:
#Vendor=0x1509
#Product=0x925d
########################################################################

[futabaMDM166A]
#  futabaMDM166A driver
#  This is an driver module for Futaba MDM166A VFD displays.
#  The VFD is built-in in Targa HTPC cases and connected to USB port.
#  Default size: 96 x 16
Driver=futabaMDM166A

#Width=96
#Height=16
#UpsideDown=no
#Invert=no
#Brightness=50
#RefreshDisplay=1000
########################################################################

[ax206dpf]
#  THIS IS AN EXPERIMENTAL DRIVER!
#  You have to uncomment the variable HAVE_DRIVER_AX206DPF
#  in Make.config to use this driver.
#  READ the READDME.ax206dpf before use!
#
# ax206dpf driver
#  This is a driver module for an AX 206 based hacked photoframe.
#
#  Default size: 320 x 240 or 240 x 320 (see "Portrait")
Driver=ax206dpf
#Width=320
#Height=240
#
# UpsideDown
#  Rotates the display output by 180 degrees. This might be useful, if
#  the LCD is mounted upside-down.
#  Possible values: 'yes', 'no'
#  Default value: 'no'
#UpsideDown=no
#
# Brightness
#  Sets the brightness of the display's backlight
#  Possible values: 0 <= x <= 100)
#  Default value: 100
#Brightness=100
#
# Device
#  Selects a specific display
#  'dpf0' = first detected display, 'dpf1' = second detected display, ...
#  Default value: 'dpf0'
#Device=dpf0
#
# Portrait
#  Select portrait or landscape mode
#  Rotate display output by 90 degrees if necessary
#  Possible values: 'yes' -> default size = 240 x 320
#                   'no' -> default size = 320 x 240
#  Default value: 'no'
#Portrait=no
#
# Zoom
#  Determines if pixels should be magnified.
#  Possible values: 1, 2, 3, 4
#  Default value: 1
#Zoom=1
#
# The following parameters are for multi-display setups only!
#
# Horizontal
#  Sets the number of displays in horizontal direction.
#  Possible values if Vertical=1: 1, 2, 3, 4
#                  if Vertical=2: 1, 2
#  Default value: 1
#Horizontal=1
#
# Vertical
#  Sets the number of displays in vertical direction.
#  Possible values if Horizontal=1: 1, 2, 3, 4
#                  if Horizontal=2: 1, 2
#  Default value: 1
#Vertical=1
#
# Flip
#  Rotates a single displays output by 180 degrees. This might be useful, if
#  some LCDs are mounted upside-down.
#  Possible values for every display : 'y', 'n'
#  Default value: 'nnnn'
#Flip=nnnn
#

########################################################################

[vncserver]
# vncserver driver
#  Output goes to a vncserver device
#  Default size: 320 x 240
Driver=vncserver
Width=320
Height=240
#
# HttpDir
#  Webclients directory of libvncserver installation (only needed for webclient access)
#HttpDir=/usr/share/webclients

########################################################################

[ssd1306]
# ssd1306 driver
#  This is a driver module for the SSD1306 OLED display controller.
#  Default size: 128 x 64
Driver=ssd1306
Device=0
Width=128
Height=64

[ili9341]
# ili9341 driver
#  This is a driver module for the ILI9341 TFT display controller.
#  Default size: 320x240
Driver=ili9341
Device=0
Width=320
Height=240

[alphacool]
# Driver setting for the Alphacool USB LCD (240x128 pixels)
# Requires serdisplib to be installed
Driver=serdisp
Controller=alphacool
Device=USB:060c/04eb
Backlight=yes

[sdcmegtron]
# Driver setting for the SDC Megtron USB LCD (240x128 pixels)
# Requires serdisplib to be installed
Driver=serdisp
Controller=sdcmegtron
Device=USB:152a/8380
Backlight=yes

[usbserlcd]
# This is the driver for displays based on the USBserLCD firmware:
# https://github.com/M-Reimer/usbserlcd
Driver=usbserlcd
Device=/dev/ttyUSB0
RefreshDisplay=0

[st7565r-reel]
# st7565r driver
#  This is a driver module for the ST7565R based Reelbox frontpanel LCD
#  Default size: 128 x 64
Driver=st7565r-reel
Device=/dev/ttyS0
Brightness=100
Contrast=80