Skip to content
This repository has been archived by the owner on Nov 18, 2020. It is now read-only.

Latest commit

 

History

History
88 lines (70 loc) · 3.16 KB

README.md

File metadata and controls

88 lines (70 loc) · 3.16 KB
Raw

lk2nd

lk2nd is a bootloader for Qualcomm MSM devices (See ## Supported SoCs), based on the CodeAurora Little Kernel fork. It provides an Android Fastboot interface on devices where the stock bootloader does not provide Fastboot (e.g. Samsung).

On MSM8916 it is also used for some quirks for mainline devices, e.g. to set a proper WiFi/BT MAC address in the device tree.

lk2nd does not replace the stock bootloader. It is packaged into an Android boot image and then loaded by the stock bootloader as a "secondary" bootloader. The real Android boot image is placed into the boot partition with 1 MB offset, and then loaded by lk2nd.

Supported SoCs

  • MSM8916
  • MSM8917
  • MSM8953 (SDM450,SDM625)
  • MSM8952 (MSM8940)

Supported devices

  • Motorola Moto G4 Play (harpia)
  • Samsung Galaxy A3 (2015) - SM-A300FU
  • Samsung Galaxy A5 (2015) - SM-A500FU
  • Samsung Galaxy J5 (2016) - SM-J510FN
  • Samsung Galaxy S4 Mini Value Edition - GT-I9195I
  • Samsung Galaxy Tab A 8.0 LTE (2015) - SM-T357W
  • Samsung Galaxy Tab A 9.7 WiFi (2015) - SM-T550
  • Wileyfox Swift
  • Samsung Galaxy A6+ (2018) - SM-A605FN
  • Xiaomi Redmi 4X - santoni
  • Xiaomi Redmi Note 4X Snapdragon - mido
  • Samsung Galaxy J4+ (j4primelte) - SM-J415*
  • Samsung Galaxy J6+ (j6primelte) - SM-J610*

Installation

  1. Download lk2nd.img (available in Releases(MSM8916))
  2. Flash lk2nd.img using the stock flashing procedure:
  • Fastboot: fastboot flash boot lk2nd.img
  • Samsung: heimdall flash --BOOT lk2nd.img

Usage

lk2nd provides the standard Android fastboot protocol for flashing/booting Android boot images.

Press Volume Down while booting to enter Fastboot mode. Press Volume Up while booting to boot into Recovery mode.

Note: If your stock bootloader uses the same key combinations, you need to wait a bit before pressing the volume keys. Usually, waiting until the screen turns on and/or the device vibrates should be enough to make the stock bootloader ignore the keys.

fastboot flash lk2nd lk2nd.img can be used to update lk2nd directory from its fastboot interface.

Note: fastboot flash boot boot.img will flash the actual boot image with 1 MB offset into the boot partition. This is done to avoid replacing lk2nd (since it is also booted from the boot partition).

Other fastboot commands work normally.

Building

$ make TOOLCHAIN_PREFIX=arm-none-eabi- <SoC>-secondary

Requirements:

Replace TOOLCHAIN_PREFIX with the path to your tool chain. lk2nd.img is built and placed into build-<SoC>-secondary/lk2nd.img.

Porting

To other devices with supported Socs

  • Add a simple device tree to dts/. You just need model and the qcom,msm-id/qcom,board-id from downstream.

To other SoCs

  • Cherry-pick changes
  • Make some changes
  • Add secondary project config

(TODO: Document this properly)

Contact

Ping minecrell/Mis012/Junak on #postmarketos-mainline.